150 - Emerson Network Power
150 - Emerson Network Power
150 - Emerson Network Power
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Description—Firetrol ® FTA1800 Autotransformer Starting<br />
Fire Pump Controllers use an autotransformer to<br />
supply reduced voltage when starting the motor. The<br />
controller is of the closed circuit type where the motor<br />
circuit remains closed during the transition from<br />
start to run resulting in minimum line disturbance.<br />
The controller monitors, displays and records fire pump<br />
system information.<br />
The autotransformer has three taps for selection of<br />
starting current and torque; 50% tap for <strong>150</strong>% current<br />
and 25% torque, 65% tap (factory setting) for<br />
250% current and 42% torque and the 80% tap for<br />
384% current and 64% torque.<br />
Approvals—Firetrol fire pump controllers are listed<br />
by Underwriters' Laboratories, Inc., in accordance with<br />
UL218, Standard for Fire Pump Controllers, CSA,<br />
Standard for Industrial Control Equipment, and approved<br />
by Factory Mutual. They are built to meet or<br />
exceed the requirements of the approving authorities<br />
as well as NEMA and the latest editions of NFPA 20,<br />
Installation of Centrifugal Fire Pumps, and NFPA 70,<br />
National Electrical Code.<br />
Standard Features—The following are included as<br />
standard with each controller:<br />
n Voltage surge protector<br />
n Main Disconnect Switch sized for connected motor<br />
horsepower and voltage<br />
n Fire pump Circuit Breaker<br />
n Motor contactor<br />
Product Description<br />
Autotransformer Starting Electric<br />
Fire Pump Controllers<br />
•<br />
FTA1800<br />
n Emergency Manual Run Mechanism to mechanically<br />
close motor contactor contacts in an emergency<br />
condition<br />
n Built-in Start and Stop push-buttons to bypass<br />
automatic start circuits<br />
n Door mounted display/interface panel featuring a<br />
40 Character Vacuum Fluorescent Display, Membrane<br />
Type User Control Push-buttons and easy<br />
to read LED Indicators<br />
n Single handle Isolating Disconnect Switch/Circuit<br />
Breaker mechanism<br />
n Transition Contactor and Autotransformer<br />
n POWER ON LED<br />
n PUMP RUN LED<br />
n PHASE FAILURE LED<br />
n PHASE REVERSAL LED<br />
n LOW PRESSURE LED<br />
n DELUGE OPEN LED<br />
n INTERLOCK ON LED<br />
n TRANSFER SWITCH NORMAL LED (If unit ordered<br />
with Automatic <strong>Power</strong> Transfer Switch)<br />
n TRANSFER SWITCH EMERGENCY LED (If unit<br />
ordered with Automatic <strong>Power</strong> Transfer Switch)<br />
n EMERGENCY ISOLATING SWITCH OFF LED (If<br />
unit ordered with Automatic <strong>Power</strong> Transfer Switch)<br />
n Minimum Run Timer / Off Delay Timer<br />
n Daylight Savings Time option<br />
n Weekly Test Timer<br />
n Motor Acceleration Timer<br />
n Elapsed Time Meter<br />
n Digital Pressure Display<br />
n 1.44M Floppy Disk Drive<br />
n Data Log<br />
n Event Log (3000 Events)<br />
n True RMS Metering with simultaneous 3 phase<br />
display of amps and volts<br />
n Disk Error message<br />
n Disk Near Full message<br />
n Pressure Error message<br />
n Motor Over 320% message<br />
n Local Start message<br />
n Remote Start message<br />
n Emergency Start message<br />
n Fail To Start message<br />
n Undervoltage message<br />
n Overvoltage message<br />
n Low Suction Pressure message<br />
n High Speed Open Serial Communications Port<br />
n NEMA Type 2 enclosure