Bedienungsanleitung und Ersatzteile für Gartenhäcksler Operating ...

Operational faults
Fault Possible cause Remedy
Motor does not start − No power supply
− Mains cable defective
− Machine overloaded
Motor hums but does not start − Cutting roller blocked
Shredding material is not
drawn into the shredder
− Capacitor faulty
− Incorrect switch position
− Shredding material caught in funnel
− Machine clogs
switch-over in the direction of rotation
− Shredding material too soft or wet
− Cutting roller worn
15
− Check fuses
− have these checked (electrician)
− Overload protection triggered
Turn On-Off switch to "0" and let machine cool down
− Turn On-Off switch to left, then switch machine off and
remove shredding material. If the blockage cannot be
removed immediately switch the On-Off switch between
cutting and reverse a number of times until the cutting
roller runs free.
− Bring machine to manufacturer or authorised workshop for
repair
− Turn On-Of switch to correct position
− Turn On-Off switch to left to release shredding material,
remove any dirt
− Switch off unit. Wait until the blades come to a standstill.
Switch unit back on and use material which is easier to
process.
− Push down with a branch and shred
− Adjust shaving plate as described in "Adjusting the
shaving plate, replace cutting roller if heavily worn
Shredding material not cut Incorrect setting of shaving plate Adjust shaving plate, if this cannot be adjusted it has to be
cleanly
replaced by the customer service department.
Device starts but blocks under Extension cable too long or cross-section Extension cable at least 1.5 mm², maximum 25 m long. If a
as slight load and switches off to small.
longer cable is used, minimum cross-section 2.5 mm².
via protective motor switch. Socket too far from mains supply and
cross-section of mains cable too small
Specifications
Model 1600 1800 2000 2200 2300 2400 2500
name of model AH 282 AH 280 AH 280 AH 281 AH 281 AH 281 AH 281
Motor AC-motor 230 V, 50 Hz, S6 = 40% ED, 2800/40 min-1 motor rating P1 = 1600 W P1 = 1800 W P1 = 2000 W P1 = 2200 W P1 = 2300 W P1 = 2400 W P1 = 2500 W
On/Off switch with: overload protection; cutting and reverse function; zero-voltage initiator
Weight 25 kg 25,5 kg 26 kg 26,5 kg 27 kg 27 kg 27 kg
Ecoustic pressure level at work LPA
(mesured to RAL-UZ 54, DIN 45635 Teil
1/05.84)
79 dB (A) 79 dB (A) 79 dB (A) 80 dB (A) 80 dB (A) 80 dB (A) 80 dB (A)
Ecoustic capacity level LWA
(mesured to RAL-UZ 54, DIN 45635Teil
1/05.84)
86 dB (A) 86 dB (A) 86 dB (A) 87 dB (A) 87 dB (A) 87 dB (A) 87 dB (A)
Ecoustic pressure level at work LPA
(mesured to 2000/14/EG)
91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A)
Measured level of the acoustic 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A) 91 dB (A)
output LWA (mesured to 2000/14/EG)
Guaranteed level of the acoustic
output LWA (mesured to 2000/14/EG)
92 dB (A) 92 dB (A) 92 dB (A) 92 dB (A) 92 dB (A) 92 dB (A) 92 dB (A)
max. branch diameter
(only for freshly cut wood)
∅ 4,0 cm ∅ 4,0 cm ∅ 4,0 cm ∅ 4,0 cm ∅ 4,5 cm ∅ 4,5 cm ∅ 4,5 cm
Safety class Ι