Manual de instrucciones - Makita

More documents

Recommendations

Info

15 16 17 18 19 20 4 24 5 27 28 30 26 25 14 10 31 18 29 17
ENGLISH 1 Base 2 Scale 3 Bit protrusion 4 Clamping nut 5 Adjusting screw 6 Switch lever 7 Loosen 8 Tighten 9 Hold 10 Workpiece 11 Feed direction Explanation of general view 12 Bit revolving direction 13 View from the top of the tool 14 Straight guide 15 Base protector 16 Screws 17 Screwdriver 18 Bit 19 Templet 20 Templet guide 21 Bolt 22 Guide plate SPECIFICATIONS Model 3709 Collet chuck capacity....................................6 mm or 1/4” No load speed (min -1 )............................................ 30,000 Overall length ......................................................199 mm Net weight............................................................... 1.5 kg Safety class ............................................................. /II Due to the continuing program of research and development, the specifications herein are subject to change without prior notice. Note: Specifications may differ from country to country. Intended use The tool is intended for flush trimming and profiling of wood, plastic and similar materials. Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire. Safety hints For your own safety, please refer to enclosed safety instructions. ADDITIONAL SAFETY RULES ENB054-1 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. Wear hearing protection during extended period of operation. 3. Handle the bits very carefully. 4. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 5. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 6. Hold the tool firmly. 7. Keep hands away from rotating parts. 8. Make sure the bit is not contacting the workpiece before the switch is turned on. 23 Wing nut 24 Clamp screw (A) 25 Centre hole 26 Nail 27 Clamp screw (B) 28 Trimmer guide 29 Guide roller 30 Limit mark 31 Brush holder cap 9. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. 10. Be careful of the bit rotating direction and the feed direction. 11. Do not leave the tool running. Operate the tool only when hand-held. 12. Always switch off and wait for the bit to come to a complete stop before removing the tool from workpiece. 13. Do not touch the bit immediately after operation; it may be extremely hot and could burn your skin. 14. Always lead the power supply cord away from the tool towards the rear. 15. Do not smear the tool base carelessly with thinner, gasoline, oil or the like. They may cause cracks in the tool base. 16. Draw attention to the need to use cutters of the correct shank diameter and which are suitable for the speed of the tool. SAVE THESE INSTRUCTIONS. FUNCTIONAL DESCRIPTION CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting bit protrusion (Fig. 1) To adjust the bit protrusion, loosen the clamping nut and move the tool base up or down as desired by turning the adjusting screw. After adjusting, tighten the clamping nut firmly to secure the tool base. Switch action (Fig. 2) To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. 5
Page 1 and 2: GB Trimmer Instruction Manual F Aff
Page 3: 16 7 8 9 10 14 24 15 11 12 23 25 21
Page 7 and 8: Align the centre hole in the straig
Page 9 and 10: ASSEMBLAGE ATTENTION : Avant d’ef
Page 11 and 12: DEUTSCH 1 Frästisch 2 Tiefeneinste
Page 13 and 14: HINWEIS: Konstruktionsbedingt könn
Page 15 and 16: DESCRIZIONE DEL FUNZIONAMENTO ATTEN
Page 17 and 18: NEDERLANDS 1 Zoolplaat 2 Schaal 3 G
Page 19 and 20: Wanneer de afstand (A) tussen de zi
Page 21 and 22: DESCRIPCIÓN DEL FUNCIONAMIENTO PRE
Page 23 and 24: PORTUGUÊS 1 Base 2 Escala 3 Saliê
Page 25 and 26: Trabalho circular Pode executar tra
Page 27 and 28: FUNKTIONSBESKRIVELSE FORSIGTIG: Sø
Page 29 and 30: SVENSKA 1 Fräskorg 2 Skala 3 Fräs
Page 31 and 32: OBSERVERA: Cirklar på en radie mel
Page 33 and 34: FUNKSJONSBESKRIVELSE FORSIKTIG: For
Page 35 and 36: SUOMI 1 Alusta 2 Asteikko 3 Terän
Page 37 and 38: Kaarevien leikkausten tekeminen Kaa
Page 39 and 40: ΛΕΙΤΥΡΓΙΚΗ ΠΕΡΙΓΡΑ
Page 41 and 42: ACCESSORIES CAUTION: These accessor
Page 43 and 44: Router bits/Fraises de défonceuse/
Page 45 and 46: Ball bearing flush trimming bit Boo
Page 47 and 48: ENGLISH EC-DECLARATION OF CONFORMIT
Page 49 and 50: For European countries only ENGLISH
Page 52: Makita Corporation Anjo, Aichi, Jap

Manual de instrucciones - Makita

Create successful ePaper yourself

Delete template?

Save as template?