TIMBERMAN DENMARK A/S Havnevej 17 · DK ... - Abio

Assembly
1. Take the gate out of it’s carrying bag.
2. The gate unfolds by pulling top and bottom parts
away from each other.
2a. Important: Make sure that the sides are
completely unfolded. The locks in either side (under
the printed marks) must "click" for correct unfold.
3. Place the gate in the opening. The top and
bottom horizontal tubes are telescopic so that the
gate can be adjusted to fit the opening by pushing
the childproof locks (b and c) underneath the fabric.
Important: The top and bottom tubes must be
adjusted alternately. If not the gate can become
skewed.
4. Important: On the spindles at top (f) and bottom
(h) (opposite the handle) is a red and yellow indicator.
The function of the indicators is to show
wheather the gate is correctly fitted or not. If the
gate is correctly fitted neither the red or the yellow
parts of the indicator are visible. If the red part of
the indicators is visible the gate should not be fitted
in this particular opening, because this means that
the opening is unable to withstand the minimum
pressure required for a safe installation.
If only the yellow parts of the indicators are visible
the gate shall be fitted with the provided wallcups
(see ill.11).
5. Using the telescope adjustment extend the gate
as wide as possible to still allow the gate to fit ín
the opening.
Final adjustment will take place later. At the bottom
the distance between the gate and the wall/door
opening shall be no more than approx. 5 mm
(2/10”) .
6. Raise the gate to an upright position and press
carefully the gate towards the floor until the bottom
lock (g) is fully engaged (6a.). Check that neither the
red or yellow part of the indicator is visible. If it is
adjust the spindle opposite the bottom lock a little
further out and position the gate and lock.
7. Open the handle (e) by pushing the button whilst
lifting the handle at the same time.
7a+b. Adjust the top spindle (f) until it touches the
wall. Adjust the spindle in the handle until the gap
between the spindle and the wall is approx. 5mm
(2/10").
8. Close the handle. Check that neither the red or
the yellow part of the indicator is visible . If they are
go back to ill. 7a+b and adjust spindle further out.
If the further adjustment fails to make the red
marking disappear the gate is not suitable for this
opening. If only the yellow marking is visible use
provided wallcups (ill.11).
9. If neither one of the indicators show the yellow
part the gate is nearly fitted.
Now adjust the locknuts towards the gate on both
top and bottom spindles and tightens as tight as
possible with your fingers. The gate is now ready
to use.
10. To remove the gate from the opening press
button (d) in handle and open handle and lift the
gate out of the opening. For re-installation place
bottom part of gate towards the floor, raise gate
upright and press gently towards the floor. Place
top part of gate in a full upright position and close
handle, the gate is now secure.
11. If Indicators show yellow marking:
Use the provided wallcups.
Place top wall cups between the top spindles and
the wall/door frame and bottom wall cups
between the bottom spindles and the wall/door
frame. Make sure that the bottom lock is fully
engaged before placing wall cups, see ill. 6a).
12. Mark out their position. Remove gate.
13. Screw in wall cups according to markings.
Note: The screws provided are only intended for
fixing into wood. If fixing to other material, use
appropriate screws and wallplugs (diameter = 4
mm).
14. Now you are reeady to install the gate
according to ill. 5-9.
15. Important: When the gate is correctly fitted
with or without wall cups the distance between the
wall and the outermost member of the gate must
not exceed 55 mm (2.2”).
16. Folding the gate
When gate is no longer needed, it can be stored in
its carrying bag.
Remove gate from opening and close handle. Push
button on top rail and slide sections together to the
next smallest width.
Repeat for bottom rail and alternate bottom and
top rails until smallest gate width is achieved. It
may also be necessary to retract spindles.
Release locks (i) are located in middle of each side,
indicated by printed icons on fabric. Doing one
side at a time, squeeze lock while gently pressing
inward. Repeat on second side.
When collapsed, top and bottom plastic hinges will
be touching.
Gate can now be placed in carrying bag.