Running Gear & Wheel Equipment Hubs & Bearings - Ifor Williams

More documents

Recommendations

Info

Page 42 1 2 3 4 5 6 7 8 9 P1258 Hub cap Grey 76mm. For trailers with bolt on knott brakes and 76mm bearings 1996 onwards. F1013Z Stake nut. Without flange. It is recommended that new nuts are fitted after servicing the brakes. F1015 Washer. Used under the F1013Z stake nut. F1014 Stake Nut M30. With flange. F1951 Circlip. 76mm internal (bearing retainer) circlip - for the current production type bearing. P00002 Bearing. Unitized bearing for hubs with a 76mm bore. HUB KITS These hub kits suit trailers manufactured from September 1992, complete with the current production bearing fitted. Each hub also comes supplied with the adaptor kit shown below to enable it to be fitted to older models with the round beam axle, Knott brakes and SKF bearings. KS0825 Hub kit. 200 x 50 brake 4 stud. Contains hub as illustrated, also includes the adaptors and components detailed above. KS0826 Hub kit. 200 x 50 brake 5 stud. Contains hub as illustrated, also includes the adaptors and components detailed above. KS0827 Hub kit. 250 x 40 brake 5 stud. Contains hub as illustrated, also includes the adaptors and components detailed above. LM146 with headboard, dropsides, meshsides, ramp and prop stands Stake nuts have been used on all trailer models since January 1994 7 8 9 Running Gear & Wheel Equipment Hubs & Bearings 1 2 3 4 5 6
Running Gear & Wheel Equipment Hubs & Bearings 1 2 3 4 1 KS0755L Brake drum. From 20th June 1988 for 6.00x9 wheels. Complete with 2 off bearings P0001 /P0002, oil seal P0004, bearing retaining washer C14679, axle end nutF1099S, grease cap C72253, 5 off wheel stud F1804, 5 off wheel nut F1813, spirol pin F1909S and split pin F1508. KS0756 Brake drum. From 20th September 1988 for 145R10, 155R13, 175R13 & 6.70x13 wheels Note: HB505R 80637,38,39,40,41 from batch 427; all from batch 437 (P0003 seal) Complete with 2 off bearings P0001 /P0002, oil seal P0004, bearing retaining washer C14679, axle end nut F1099S, grease cap C72253, 4 off wheel stud F1801, 5 off wheel nut F1811, spirol pin F1909S and split pin F1508. KS0757L Brake drum. From 15th February 1988. DP120G, LL106G, LL126G, LL146G (225R10 wheel)(DP120G batch 291, LL batch 286)Complete with 2 off bearings P0001 /P0002, oil seal P0004, bearing retaining washer C14679, axle end nut F1099S, grease cap C72253, 5 off wheel stud F1804, 4 off wheel nut F1813, spirol pin F1909S and split pin F1508. P0001 Bearing cup. All trailers to September 1992 (HB401 until April 1993) requires bearing P0002. P0002 Bearing cone. All trailers to September 1992 (HB401 until April 1993) requires cone P0001. P0081 Oilseal. Most models (pre 1978). P0003 Oilseal. 43 x 75 x 10mm. P0004 Oilseal. 55 x 75 x 10mm. HB511 2 Older Models 3 4 5 5 6 7 8 9 10 11 6 9 10 7 8 F1811 Wheel nut. M12 x 1.5mm pitch (1976-1992). F1813 Wheel nut. M16 x 1.5mm pitch (1976-1992). P1250 Hub cap Black 75mm. For trailers with weld on knott brakes and 75mm bearings 1992-1996. C72253 Hub cap. For trailers with Al-Ko brakes and taper roller bearings 1981-1992. F1098S Axle end nut. 3/4" BSF six slotted axle end nut for early trailers with solid beam axles. F1099S Axle end nut. 3/4" BSF ten slotted axle end nut for later trailers with solid beam axles. F1508 Split pin. 1-1/2" long x 5/32" diameter. F1502SS Split pin. 1 long x 5/32” diameter stainless steel. C14679 Washer. Bearing retaining washer for older round section axles. 11 Page
Page 1: Running Gear & Wheel Equipment Hubs
Page 5 and 6: Running Gear & Wheel Equipment Axle
Page 7 and 8: Running Gear & Wheel Equipment Whee

Running Gear & Wheel Equipment Hubs & Bearings - Ifor Williams

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?