wall covering instructions - Materials Inc.

Recommendations

Info

WALL COVERING INSTRUCTIONS DRYWALL APPLICATION ADHESION Prepare the adhesive according to the manufacturer’s instructions. Once the adhesive has been prepared roll an even, medium, coat over the whole wall. Once covered com- on it’s back with a short napped roller. While the adhesive is still wet begin applying the veneers one at a time, the edges and refrain from getting adhesive on the veneer surface and pushing across the grain to smooth the surface. FINISHING IMPORTANT NOTE We suggest completing a thorough test of this product. These instructions are based on standard industry product application. Stop work immediately if job is not progressing to satisfaction. We warrant the integrity of our veneers but do not have control over its use and processing. Therefore, WTP Corporation is not responsible for your application or work you undertake. 40 Burlews Court, Bldg. 1, Hackensack, NJ 07601 T. 201.968.0101 showroom 472 Broome Street, New York, NY 10013 T. 212.966.0850 mi source for interiors. | 1.866.989.1111 | www.materialsinconline.com
PROFESSIONAL WALL COVERING PRODUCTS DYNAMITE ® 111 HEAVY DUTY CLAY NON-STRIPPABLE WALLCOVERING ADHESIVE • Maximum dry adhesion • Prevents seam spreading and curling • Strong wet tack Dynamite 111 Heavy Duty Clay Non-Strippable Wallcovering Adhesive contains high solids to assure fast grab and a strong, durable • Prevents seam spreading and curling • Ideal for dry hanging paper-backed foils, Mylar® and fabrics SURFACE PREPARATION Surface must be clean and free of oil, dust, dirt, grease, mildew, and other foreign matter. For best results, use Dynamite All-Purpose - mite Non-Shrink Spackling prior to priming. Plaster – New plaster must age at least 30 days before hanging wallcovering. Prime with Dynamite 221 or 222. Drywall – New drywall must be wiped down with a damp cloth to remove dirt, grease, wax and peeling paint. Prime with Dynamite 221 or 222. Other Porous Surfaces – Walls must be clean, dry, smooth and structurally sound. Prime with Dynamite 221 or 222. Glossy Surfaces – Ceramic tile, glossy paint, existing vinyl wallcoverings, Formica®, glass, plastic or baked enamel should be primed with Dynamite 221, 222 or 235. Commercial Grade II & III – Prime with Dynamite 235 when hanging heavy weight commercial-grade papers. DO NOT USE OVER OIL/ALKYD PAINT/PRIMER OR VARNISH UNLESS IT IS PRIMED WITH A DYNAMITE ACRYLIC PRIMER. APPLICATION Mix well before using to ensure even consistency. For lightweight wallcoverings, thin as needed, up to 1 pint of water per gallon. Apply - ing time according to manufacturer’s instructions. IMMEDIATELY remove adhesive from face of washable wallcoverings and adjacent surfaces with a clean, wet sponge. HANG WALLCOVERING ACCORDING TO MANUFACTURER’S INSTRUCTIONS. COVERAGE Five gallons of adhesive will hang up to 40 single rolls. (1,400 sq. ft./5 gal.). Coverage rates can vary depending on condition of the substrate, priming and sizing, weather conditions and method of application. For more product information on Dynamite Wallcovering adhesive contact: Gardner-Gibson, Inc. • P.O. Box 5449 • Tampa, Florida 33675-5449 Phone: (813) 248-2101 • Fax (813) 248-6768 • www.gardner-gibson.com 40 Burlews Court, Bldg. 1, Hackensack, NJ 07601 T. 201.968.0101 showroom 472 Broome Street, New York, NY 10013 T. 212.966.0850 mi source for interiors. | 1.866.989.1111 | www.materialsinconline.com
Page 1: WALL COVERING INSTRUCTIONS DRYWALL
Page 5: PROFESSIONAL WALL COVERING PRODUCTS

wall covering instructions - Materials Inc.

Create successful ePaper yourself

Delete template?

Save as template?