optibelt - Agera Industritillbehör AB

optibelt S=C PLUS optibelt M=S
Optibelt S=C PLUS – Power Transmission for perfectionists
Twenty years of continuous development have made a V-belt
which cannot be more precise. The expression S=C PLUS has
become a synonym for absolute use in matched sets. Machines
of every kind are equipped worldwide with Optibelt S=C PLUS,
in every location where specifi c requirements are demanded.
Why this is so is shown by the following tolerance list.
Section SPZ from 1212 up to 4500 mm L d
Section SPA from 1207 up to 4500 mm L d
Section SPB from 1250 up to 10 000 mm L d
Section SPC from 2000 up to 10 000 mm L d
Section 3V/ 9N from 3V 500 up to 3V 1400
Section 5V/15N from 5V 500 up to 5V 3550
Section 8V/25N from 8V 1000 up to 8V 3750
+ closest tolerances – unrestricted
use in matched sets
+ energy saving operation
These are your advantages:
Optibelt M=S – the bearer of performance
Comparison of tolerance of Optibelt S=C PLUS versus BS, DIN and RMA/MPTA Standards
Wedge belts to BS 3790 and DIN 7753 Part 1
V-belts to BS 3790 and DIN 2215
Section Z/10 from 1550 up to 4500 mm L d
Section A/13 from 1200 up to 10 000 mm L d
Section B/17 from 1200 up to 10 000 mm L d
Section 20 from 1250 up to 10 000 mm L d
Section C/22 from 1200 up to 10 000 mm L d
Section 25 from 1400 up to 10 000 mm L d
Section D/32 from 2000 up to 10 000 mm L d
Section E/40 from 3000 up to 10 000 mm L d
Wedge belts to USA Standard RMA/MPTA
All belts are unrestrictedly usable in matched sets. As for the S=C
PLUS the highly precise manufacturing process and the matured
material technology provide for closest tolerances. Optibelt M=S
meets all valid standards worldwide for V-belt sets.
V-belt
datum length L d
(mm)
> 1200 ≤ 2000 ± 2 12 to 20 mm
> 2000 ≤ 5000 ± 2 20 to 50 mm
> 5000 ≤ 8000 ± 4 50 to 80 mm
> 8000 ≤ 10 000 ± 6 80 to 100 mm
V-belt length
(mm)
S=C PLUS
tolerances
(mm)
S=C PLUS
tolerances
(mm)
> 1200 ≤ 1600 ± 2
> 1600 ≤ 2000 ± 2
> 2000 ≤ 2500 ± 2
> 2500 ≤ 3150 ± 2
> 3150 ≤ 4000 ± 2
> 4000 ≤ 5000 ± 2
> 5000 ≤ 6300 ± 4
> 6300 ≤ 8000 ± 4
> 8000 ≤ 10 000 ± 6
The extremely positive ratio between standard and Optibelt
tolerances is also applicable to these sections.
Please take exact data from our technical literature.
+ reduced vibration
+ extended maintenance intervals
+ longer belt life
= optibelt V-belts
Acceptable
DIN-tolerances
(mm)
Acceptable
DIN-tolerances
(mm)
+ 23 / –11
+ 27 / –13
+ 31 / –16
+ 37 / –18
+ 44 / –22
+ 52 / –26
+ 63 / –32
+ 77 / –38
+ 93 / –46
175