WT Glover, Electric Wire & Cables 1897

CLOVERS'
ANTI-FOUOALT MATERIAL
PATENT ARMATURE BARS, with solid ends.
Below will be found the sizes of the tools we already have, others are being
added from time to time,
SQUARE OR RECTANGULAR SIZES.-The dimensions given
below are the widths of tools we have and are unalterable, but we can vary
the size the other way to any dimension up to a square, i,e, :-
'250" x '250" can alter to '250 x '180 or '250 x '110, &c,
Size one way Size ODe way ~ize one way Size one way Size one way Size one way
in Inches. in Inches. in Inches. in Inches. in Inches" in Inches.
2'460 '770 '560 '400 '296 '185
2'000 '745 '554 '390 '285 '180
1'490 '670 '510 '375 '280 '165
1'230 '664 '500 '370 '276 '155
1'100 '645 '495 '350 '255 '150
1'000 '630 '480 '325 '250 '136
'842 '610 '455 '320 '225 '133
'812 '600 '450 '310 '220 '120
'800 '580 '435 '305 '200 '113
'700 '570 '430 '300 '105 '110
TAPERED SECTIONS.-The sizes given below are unalterable as
regllJ'ds the depth of the bar, but they can vary in width as much as
desired, the taper always remaining the same, i e, :~
'560 tapering 48 mils, may be '560 x '560 tapering to '512,
or '560 x '300 tapering no '252,
Size in Inch, Size in Inch, Size in Ineb.
1'200 tapering 65 mils, '670 tapering 48 mils, '450 tapering 27 mils.
1'050 40
'650 20
'450 18
1'000
20
'650
20
'370
20
'045
38
'640
20
'350
10
'000
'20
'625
30
'340
12
'850
20
'600 "
.. 20
'330 25
'800 30
'600 35
'200
10
'750
27
'560
48
'270
10
'700
32
'560
30
'262
10
'700
20
'520
120
'255
7
'700 "
4
'500
31 " '245 " "
"
3
'700 .. 40
"
"
We have some semi~circulartools for making half-round sections. Bars can be
rounded throughout or may have the rounded section on the top side at one end and
underneath at the other, the centre being rectangular or square as required.
COMPRESSED STRAND IN CONTINUOUS LENCTHS.
We supply the above bare and insulated as may be required, prices of which are
as follows:-
Bare sections over !" square for Armatures (including Royalty).. IS. 3d. per lb. nett.
" " Magnets (no Royalty) 1s. " "
Insulating with fine cotton braid not exceeding 25 mils, '. , , , . '. l~d.
" 8.C.C. and fine braid" 32" 2§-d. " "
" double braid ,,50 " 4d. " "
Solid ends are charged according to size and the amount of tooling required, and
whether tinned or plain,
[ 70]
"
"
"
SPEOIAL MATERIAL
OR
ARMATURES,
&0.
We manufacture every description of wire and cable required
for Armature work, amongst which are the following :-
BARE ARMATURE BARS (WITH OR WITHO~T SO~ID
ENDs).-The price for these is Is. 3d. per lb. nett, mcl~dmg
Royalty. Solid Ends are extra and charged accordmg to
size and the amount of shaping and tooling required, and
whether tinned or plain; if insulated the extras would be
as on previous page. We can give prompt delivery of
any section whether listed or not.
SOLID ROUND WIRES.-Double Cotton Covered. Special
basis price to dynamo manufacturers. All sizes thicker
than No. l5's finely braided instead of D.C.C. (double
cotton covered) ld. per lb. nett extra to D.C.C. basis.
SOLID SECTIONAL STRIP.-Any dimensions at ld. per
lb. nett more than round wire.
LAMINATED STRIP.-Special Fine Braid. Any dimensions,
3d. per lb. nett more th%'n D.C.C. round wire.
STRANDED CABLES (NOT COMPRESSED). D.C.C. ld. per
lb. more than solid wire. Finely braided, instead of
D.C.C., 2d. per lb. more than solid wire. Any of the
abo'Ve will be varnished at a uniform rate of ld. per lb.
nett. Tinned wire extra, according to size.
DIATRITE VARNISH, for Armatures.
SPECIAL TAPE, for Armatures.
COPPER WIRE AND TAPE, etc., for all electrical purposes.
HIGH CONDUCTIVITY COPPER CASTINGS supplied
to order.
Goods paoked and delivered f.o.b. 2! per o.ent extra.
[ 71 ]