<strong>06.13</strong> TABELLER/TEKNISK INFORMASJON Gjengeoversikt Utv. diam. mm Stigning BSP (T) (K) R Metrisk JIC/UNF NPTF / NPSM ORFS Innv. diam. mm 9,3-9,7 28 GPT 1/8” 8,5-8,9 9,3-9,7 29 GPT 1/8” 8,5-8,9 9,7-9,9 1,5 M 10x1,5 8,2-8,6 10,9-11,1 20 GPT 7/16”-20 9,7-10,0 11,6-11,9 1,5 M 12x1,5 10,2-10,6 12,4-12,7 20 GPT 1/2”-20 11,3-11,6 12,9-13,1 19 GPT 1/4” 11,4-11,9 12,9-13,1 18 GPT 1/4” 11,4-11,9 13,6-13,9 1,5 M 14x1,5 12,2-12,6 14,0-14,3 18 GPT 9/16”-18 12,7-13,0 14,0-14,2 18 TPI 9/16”-18 12,9-13,1 15,6-15,9 1,5 M 16x1,5 14,2-14,6 16,3-16,6 19 GPT 3/8” 14,9-15,4 16,3-16,6 18 GPT 3/8” 14,9-15,4 17,3-17,5 16 TPI 11/16”-16 15,8-16,0 17,6-17,9 1,5 M 18x1,5 16,2-16,6 18,7-19,0 16 GPT 3/4”-16 17,3-17,6 19,6-19,9 1,5 M 20x1,5 18,2-18,6 20,4-20,6 16 TPI 1 3/16”-16 19,1-19,3 20,5-20,9 14 GPT 1/2” 1/2” 18,6-19,0 21,6-21,9 1,5 M 22-1,5 20,2-20,6 22,0-22,2 14 GPT 7/8”-14 20,2-20,5 22,6-22,9 14 GPT 5/8” 5/8” 20,6-21,0 23,6-23,9 1,5 M 24x1,5 22,2-22,6 25,1-25,3 14 TPI 1”-14 23,7-23,9 25,6-25,9 1,5 M 26x1,5 24,2-24,6 26,1-26,4 14 GPT 3/4” 3/4” 24,1-24,5 26,6-26,9 12 GPT 1 1/16”-12 24,4-24,7 29,6-29,9 2 M 30x2 27,4-27,8 29,8-30,1 12 GPT 1 3/16”-12 27,6-27,9 29,8-30,0 12 GPT 1 3/16”-12 28,0-28,2 29,6-29,9 1,5 M 30x1,5 28,2-28,6 33,0-33,2 11 GPT 1” 30,3-30,8 33,0-33,3 12 GPT 1 5/16”-12 30,8-31,2 32,9-33,4 11,5 GPT 1” 30,3-30,8 35,6-35,9 2 M 36-2 33,4-33,8 36,2-36,4 12 TPI 1 7/16”-12 34,4-34,6 37,6-37,9 1,5 M 38x1,5 36,2-36,6 40,9-41,2 12 GPT M 38-1,5 38,7-39,1 41,6-41,9 2 M 42,2 39,4-39,8 41,5-41,9 11 GPT 1 1/4” 39,0-39,5 41,4-42,0 11,5 ,GPT 1 1/4” 39,2-39,6 12 TPI 1 11/16”-12 40,9-41,1 44,6-44,9 2 M 45x2 42,4-42,8 44,6-44,9 1,5 M 45x1,5 43,2-43,6 47,3-47,6 12 GPT 1 7/8”-12 45,1-45,5 47,4-47,8 11 GPT 1 1/2” 44,8-45,3 47,3-47,9 11,5 GPT 1 1/2” 45,1-45,5 51,6-51,9 2 M 52x2 49,4-49,6 51,6-51,9 1,5 M 52x1,5 50,2-50,6 59,4-59,8 11 TPI 2” 2 1/2”-12 2” 56,5-56,7 59,8-60,2 11,5 TPI 56,4-56,7 63,3-63,6 12 TPI 61,3-61,8 Skyvelæret hjelper med identifikasjon Gjengelæret må helt til bunns! Se godt mot lys! <strong>06.13</strong>.0102 Ø utv. (han, male) toppgj. koniske Ø utv. (han, male) toppgj. sylindriske Ø innv. (hun, female) toppgj. sylindriske Ø innv. (hun, female) toppgj. konsike Stigning i mm. pr. gjenge Forsøk altid nærmest mål over og under for å dobbeltkontrollere
<strong>06.13</strong> TABELLER/TEKNISK INFORMASJON Nomogram 06 GJENGEFORKORTELSER: N.P.S. American National Pipe Thread – Stright N.P.S.M. American National Pipe Thread – Stright Mechanical N.P.T. American National Pipe Thread – Taper N.P.T.F. American National Pipe Thread – Taper (Dry seal) N.P.T. American National Standard Thread – Straight R. Rørgjenger = BSP R.T. British Round Thread S.A.E. Society of Automative Engineers (45°) U.R.T. Dennis Urban Round Thread U.N.C. Unified Coarse Thread U.N.F. Unified Fine Thread VEE Shelvoke & Drewry «VEE» Round Thread W. Whitworth Thread A.P.I. American Petroleum Institute Taper Thread A.S.S.P.T. American National Straight Pipe Thread A.S.T.P.T. American National Taper Pipe Thread B.S.P. British Standard Parallel Pipe Thread B.S.T.P. British Standard Taper Pipe Thread G.H.T. Garden Hose Threads/F.P.T. – Female Pipe Thread I.P.T. American Iron Pipe Thread – Straight J.I.C. Joint Industry Conference (SAE 37°) J.I.S. Japaneese Industrial Standard M. Metric Thread M.M. Metric Thread <strong>06.13</strong>.0103