Price List - Becker Equipment,Inc.

More documents

Recommendations

Info

Typical Installations The installations below are typical installation examples only. Consult your Engineering Department for the appropriate installation of your application or call the factory for advice. Optional Pigtail assembly Optional valve and fitting assembly Calibration cylinder vented to atmosphere 10 Call Toll Free 1-800-776-6580
ACCUDRAW ® Polypropylene Cylinder Calibration Instructions Note: Before starting the calibration procedure below, ensure that the pump is primed and void of any trapped air. Using the ml scale: (scale is based on volume pumped, over any given time) 1. Fill the calibration cylinder to the top mark with the liquid to be dispensed. This can be accompished accomplished by manually filling the cylinder, or, if the the feed feed tank tank level level is higher is higher than than the the cylinder, by opening the the isolation valve valve below below the cylinder and back filling the cylinder. Caution: Never leave unattended when back filling the cylinder. 2. With the calibration cylinder full of the liquid to be dispensed, start the metering pump and operate at 100% output until all air is removed from both suction lines and pump head. 3. Shut pump “OFF”. 4. With calibration cylinder full, close isolation valve (#2) from supply tank, and open isolation valve (#1) below cylinder. 5. Start the pump. 6. Using a stop watch, measure the volume dispensed in 60 seconds. 7. Multiply the measured volume by 60 to find your ml per hour volume. 8. Adjust the pump volume control, higher or lower to meet with your desired output. 9. Repeat above steps 4 through 8 until your desired output is met. If you wish to shorten the time of dispensing for calibration by one half (1/2) or one quarter (1/4), you must multiply the volume by the same number used to divide the time by to determine ml per minute or hour. e.g. 100 ml in 60 seconds equals 50 ml X 2 in 30 seconds or 25 ml X 4 in 15 seconds Typical Installations ("A" and "B") Conversion Factors 1ml = 1 cc 1000 ml – 1 liter ml/sec x 60 = ml/min 1 US gal/min x 0.063 = liters/sec 1 US gal = 3.786 liters Caution: Do not use as a pressure vessel. Call Toll Free 1-800-776-6580 11
Page 1 and 2: ACCUDRAW ® Calibration Cylinders T
Page 3 and 4: Call Toll Free 1-800-776-6580 3
Page 5 and 6: Call Toll Free 1-800-776-6580 5
Page 7 and 8: ACCUDRAW CUSTOM CALIBRATION CYLINDE
Page 9: ACCUDRAW CUSTOM CALIBRATION CYLINDE
Page 13 and 14: ACCUDRAW ® Glass Cylinder Calibrat
Page 15 and 16: OPTIMIZING METERING PUMP APPLICATIO
Page 17 and 18: ACCU-PULSE Pulsation Dampeners (Cha
Page 19 and 20: ACCU-PULSE I Pulsation Dampeners Su
Page 21 and 22: ACCU-PULSE II Pulsation Dampeners S
Page 23 and 24: ACCU-PULSE III Pulsation Dampeners
Page 25 and 26: Body Material ACCU-PULSE APX Series
Page 27 and 28: ACCU-PULSE II / IIF Series & III /
Page 29 and 30: ACCU-VENT Automatic Degassing Valve
Page 31 and 32: Model Body Material Valve Material
Page 33 and 34: PFS CORPORATION STOPS VALVE ASSEMBL
Page 35 and 36: PFS Injection Quills Standard Featu
Page 37 and 38: PFS Injection Quills Primary Fluid
Page 39 and 40: PFS Injection Quills Standard Featu
Page 41 and 42: PFS Injection Quills Primary Fluid
Page 43 and 44: TOP VALVE * *pat. #5,857,486 & 5,94
Page 45 and 46: Welded Flanged Metallic Valves This
Page 47 and 48: High Temperature Series This series
Page 49 and 50: Parts Breakdown Schematic 4 9 10 1
Page 51 and 52: TOP VALVE PARTS USA SUGGESTED PRICE
Page 53 and 54: Clamping Device for TOP VALVE, back
Page 55 and 56: OPTIONAL EQUIPMENT PRICE LIST Acces
Page 57 and 58: Terms and Conditions Minimum order
Page 59 and 60: I N D E X ACCUDRAW CALIBRATION CYLI
Page 61 and 62:
PFS CORPORATION STOP - PLASTIC - EX
Page 63 and 64:
Accudraw Calibration Cylinder - AC#
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Accudraw Calibration Cylinder - PV#
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Accudraw Calibration Cylinder - ACS
Page 77 and 78:
Accudraw Calibration Cylinder - ACS
Page 79 and 80:
Terms Prices quoted are in Canadian
Page 81 and 82:
Top Valve CODE E Item # Description
Page 83 and 84:
Top Valve CODE E Item # Description
Page 85 and 86:
Recommended Spare Parts Pro-Kit COD
Page 87 and 88:
TOP VALVE - 2 PORT CODE E Item # De
Page 89 and 90:
TOP VALVE - 2 PORT CODE E Item # De
Page 91 and 92:
Top Valve - High Temperature CODE E
Page 93 and 94:
Page 95 and 96:
Top Valve - 2 Port - High Temperatu
Page 97 and 98:
Page 99 and 100:
Top Valve - High Pressure CODE E It
Page 101 and 102:
Top Valve - High Pressure CODE E It
Page 103 and 104:
Top Valve - 2 Port - High Pressure
Page 105 and 106:
AccuPulse Pulsation Dampener - API/
Page 107 and 108:
AccuPulse Pulsation Dampener - API/
Page 109 and 110:
AccuPulse Pulsation Dampener - APII
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
AccuPulse Pulsation Dampener - APX
Page 119 and 120:
PFS Injection Quill - IQ - Plastic
Page 121 and 122:
CODE E Part # To Suit Model # Descr
Page 123 and 124:
PFS Injection Quill - IQ - Alloy CO
Page 125 and 126:
PFS Corporation Stop - Plastic - Ex
Page 127 and 128:
70 Recommended Spare Parts Pro-Kit
Page 129 and 130:
Page 131 and 132:
PFS Corporation Stop - Alloy Item #
Page 133 and 134:
76 Recommended Spare Parts Pro-Kit
Page 135 and 136:
Accuvent - AV - Exploded Parts View
Page 137:
Metering Pump Accessories Save $$$$
show all

Price List - Becker Equipment,Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?