CPA 08 Manual - KSdigital

More documents

Recommendations

Info

Diagram 1 Front view of the C5 1 2 Front View 1. Bass/mid-range loudspeaker 2. Tweeter 3. LED 4. Groove for front grill 4 3 Diagram 2 Rear view of the C5 Operating Controls 6 7 8 9 Rear View 5. Balanced XLR input 6. Gain: Input sensitivity + 6/-10dB 7. High: Control for room adjustment in High frequency range +/- 6dB (see Diagram 3) 8. Bass: Control for room adjustment in bass/mid range +/- 6dB (see Diagram 3) 9. Bass reflex ports 10. 230 V or 115 V AC IEC connector socket 11. Fuseholder 12. On/ Off power switch 13. Black cooling fins for the output stage 5 13 12 10 11
1 Bass/mid-range driver: The 6.5” (16.5cm) high performance bass/mid-range driver of the C5 utilizes an extremely stiff carbon fiber membrane with a strong magnet as its motor. It was developed especially for the C5 and combines high impulse fidelity with a large voice coil for the reproduction of bass frequencies at high volumes. In addition, the membrane is designed to be the wave-guide for the tweeter. 2 Tweeter: The 1” (2.54 cm) dome tweeter for high frequencies is driven by an extremely strong neodymium magnet and reproduces frequencies far above 20 kHz with a minimum of distortion. 3 LED: The blue Light Emitting Diode (LED) illuminates to indicate when the system is switched on. 4 Mounting the Protective Grill: The accompanying protective grill for the loudspeaker needs only be pressed into both of the grooves. 5 Input: The balanced XLR analog input can be driven with a nominal level of up to +26dbu. 6 Input Gain: The recessed input level control provides a continously variable range of +6/-10dB. A small flat head screwdriver of approx. 2.4 mm or smaller is needed to make adjustments and is not included with the unit. 7 High Gain: The recessed input level control provides the possibility to compensate for specific acoustic problems in the listening area with high frequency response. The control provides a range of+/-6dB. (see Dia ram 3). A small flat head screwdriver of approx. 2.4 mm or smaller is needed to make adjustments and is not included with the unit. 8 Low Gain: The recessed input level control provides the possibility to compensate for specific acoustic problems in the listening area with the low frequency response. The control provides a range from +/-6dB (see diagram 3). A small flat head screwdriver of approx. 2.4 mm or smaller is needed to make adjustments and is not included with the unit. 9 Bass Reflex Ports: With the help of the bass reflex principle, the lower end of the C5’s frequency range is extended. The ports must not be blocked or covered. They are situated at the rear of the speaker. 10 IEC Plug: 230v / 115v AC IEC connector socket. 11 Fuse: specified, 1.6 slow blow for 115v / 0.8 slow blow for 230v 12 On/Off Switch: The power on/off switch disconnects the C5 completely from the mains. No power is used as long as the switch is in the Off position. 13 Cooling: There are two powerful output stages with a maximum power output of over 300W in total. The black cooling fins heat up during operation. They must no be covered or blocked. Therefore plase ensure there is good ventilation behidn the uni at all times. Diagram 3: low/mid and high frequency filters response curves shown in maximum position
Page 1 and 2: Instruction Manual C5 Active Studio
Page 3: Thank you for choosing these monito
Page 7 and 8: System Specifications Lower cut-off

CPA 08 Manual - KSdigital

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?