MacAllister MBCP254 Brush Cutter - Service Link

More documents

Recommendations

Info

14 TROUBLESHOOTING / TECHNICAL SPECIFICATIONS EN 9. TROUBLESHOOTING PROBLEM LIKELY CAUSE SOLUTION 1) The engine will not start or will not keep running – Incorrect starting procedure – Dirty spark plug or incorrect distance between the electrodes – Air filter clogged – Carburetion problems – Follow the instructions (see chapter 6) – Check the spark plug (see chapter 8) – Clean and/or replace the filter (see chapter 8) – Contact your dealer 2) The engine starts but is lacking in power – Air filter clogged – Carburetion problems – Clean and/or replace the filter (see chapter 8) – Contact your dealer 3) The engine runs irregularly and lacks in power when revved – Dirty spark plug or incorrect distance between the electrodes – Carburetion problems – Check the spark plug (see chapter 8) – Contact your dealer 4) The engine gives off an excessive amount of smoke – Incorrect composition of the fuel mixture – Carburetion problems – Prepare the fuel mixture according to the instructions (see chap. 5) – Contact your dealer 10. TECHNICAL SPECIFICATIONS Engine ................................ 2-stroke air-cooled Capacity / Power MBCP254 ........................... 25.4 cm 3 / 0.7 kW Engine rotation speed at tick-over MBCP254 .......................... 2650-2950 rpm Maximum engine rotation speed MBCP254 ................................. 11500 rpm Maximum tool rotation speed - (3 point blade) MBCP254 ................................... 9000 rpm Tank capacity MBCP254 ..................................... 650 cm 3 Maximum permitted blade diameter 3 point blade .................................. Ø 255 mm MBCP254 .......................................... 7.1 kg Weight 1) 1) Weight as per standard ISO 11806 (without fuel. cutting devices and guards) Spark plug .............................. Torch L8RTC or NGK-R BPMR7A or equivalent Mixture .......... Petrol : 2-stroke oil = 50:1 = 2%
TECHNICAL SPECIFICATIONS 15 EN Model Maximum noise and vibration levels MBCP254 Operator ear noise pressure level (EN ISO 22868) with line cutter head dB(A) 102 Measurement uncertainty (2006/42/EC - EN 27574) dB(A) 3 Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 1,5 with 3-point blade dB(A) 95 Measurement uncertainty (2006/42/EC - EN 27574) dB(A) 3 Measured sound power level (EN ISO 22868) with line cutter head dB(A) 111 Measurement uncertainty (2006/42/EC - EN 27574) dB(A) 3 with 3-point blade dB(A) 105 Measurement uncertainty (2006/42/EC - EN 27574) dB(A) 3 Vibrations transmitted to the hand on the front handgrip (“MONO”) (ISO 22867) with line cutter head m/sec 2 – Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 – with 3-point blade m/sec 2 – Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 – Vibrations transmitted to the hand on the rear handgrip (“MONO”) (ISO 22867) with line cutter head m/sec 2 – Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 – with 3-point blade m/sec 2 – Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 – Vibrations transmitted to the hand on the left handgrip (“DUPLEX”) (ISO 22867) with line cutter head m/sec 2 1,76 Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 1,5 with 3-point blade m/sec 2 0,432 Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 1,5 Vibrations transmitted to the hand on the right handgrip (“DUPLEX”) (ISO 22867) with line cutter head m/sec 2 3,19 Measurement uncertainty (2006/42/EC - EN 12096) m/sec 2 1,5 with 3-point blade m/sec 2 0,356
Page 1 and 2: Brushcutter MBCP254 DUPLEX OPERATOR
Page 3 and 4: ii 1 2 2 5 4 1 4 1 2 3 5 7 6 3 7 7
Page 5: iv 16 17 1 3 2 2 18 19 0,5 mm 1 20
Page 8 and 9: 2 EN IDENTIFICATION OF MAIN COMPONE
Page 10 and 11: 4 EN SAFETY REQUIREMENTS 3. SAFETY
Page 12 and 13: 6 MACHINE ASSEMBLY EN 4. MACHINE AS
Page 14 and 15: 8 PREPARING TO WORK / HOW TO START
Page 16 and 17: 10 EN USING THE MACHINE 7. USING TH
Page 18 and 19: 12 MAINTENANCE AND STORAGE EN 8. MA
Page 22: 16 ACCESSORIES EN 11. ACCESSORIES T

MacAllister MBCP254 Brush Cutter - Service Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?