caution - Toro
caution - Toro
caution - Toro
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
11.Remove fan hub and fan from hydraulic fan motor<br />
(Fig. 14).<br />
1<br />
2 3<br />
4<br />
5<br />
A. Remove hex nut (item 9) and washer (item 8) that<br />
secure fan hub and fan assembly to fan motor.<br />
NOTE: The fan motor shaft is tapered.<br />
B. Use suitable puller to remove fan hub (with fan attached)<br />
from fan motor shaft taking care to not damage<br />
fan. Remove fan hub and fan from machine.<br />
6<br />
7<br />
8<br />
12.Remove transport cylinder assembly from engine<br />
mount (Fig. 15). It is not necessary to remove the hydraulic<br />
hose from the cylinder. Locate and remove shim<br />
plate(s) from between transport cylinder and engine<br />
mount.<br />
IMPORTANT: The hydraulic pump assembly can remain<br />
in machine during engine removal. To prevent<br />
pump from shifting or falling, make sure to support<br />
pump assembly before mounting fasteners are removed.<br />
13.Support hydraulic pump assembly. Remove fasteners<br />
that secure pump assembly to engine (see Pump<br />
Assembly Removal in the Service and Repairs section<br />
of Chapter 4 -- Hydraulic System).<br />
14.Make sure all cable ties securing the wiring harness,<br />
fuel lines or hydraulic hoses to the engine are removed.<br />
15.Connect hoist or lift to the lift tabs on engine.<br />
16.Remove flange nuts, rebound washers and cap<br />
screws securing the engine mounts to the engine supports.<br />
1. Lock nut<br />
2. Flat washer<br />
3. Throttle lever<br />
4. Lock nut<br />
5. Flange head screw<br />
6. Cap screw<br />
27 to 33 ft -lb<br />
(37to44N-m)<br />
11 10<br />
8 9<br />
12<br />
Figure 13<br />
11<br />
10<br />
7. Flange head screw<br />
8. Spring washer (2 used)<br />
9. Ball joint<br />
10. Cap screw (2 used)<br />
11. Throttle cable<br />
12. Cable support<br />
1<br />
3<br />
9<br />
2<br />
CAUTION<br />
One person should operate lift or hoist while<br />
another person guides the engine out of the machine.<br />
IMPORTANT: Make sure not to damage the engine,<br />
fuel and hydraulic lines, electrical harness or other<br />
components while removing the engine.<br />
17.Carefully remove engine assembly from the machine.<br />
7<br />
6<br />
1. Fan motor<br />
2. Cap screw (2 used)<br />
3. Flat washer (2 used)<br />
4. Fan motor bracket<br />
5. Lock nut (2 used)<br />
6. Washer (4 used)<br />
5<br />
12 to 14 ft -lb<br />
(17to18N-m)<br />
Figure 14<br />
4<br />
7. Cap screw (4 used)<br />
8. Hex nut<br />
9. Washer<br />
10. Fan hub<br />
11. Fan<br />
18.If necessary, remove engine mounts from the engine<br />
using Figure 9 as a guide.<br />
Engine Installation (Fig. 9)<br />
1. If removed, install engine mounts to the engine using<br />
Figure 9 as a guide.<br />
2. Connect hoist or lift to the engine lift tabs.<br />
Kubota Diesel Engine<br />
Page 3 - 14<br />
Groundsmaster 4000--D
Change language