IndustrIal Chargers and dC systems

More documents

Recommendations

Info

Ratings SPR - Single Phase Rectifier SPR - Output Output Voltage Vdc Output Current A 24V 5 10 15 25 35 50 75 100 48V 5 10 15 25 35 50 75 100 110V 5 10 15 25 35 50 - - 220V 5 10 15 25 - - - - Information on other output voltages available on request. Type example: 24SPR10 = SPR 24V/10A TPR - Three Phase Rectifier TPR - Output Output Voltage VDC Output Current A 24V 25 50 75 100 125 150 200 250 >250 48V 25 50 75 100 125 150 200 250 >250 110V 25 50 75 100 125 150 200 250 >250 220V 25 50 75 100 125 150 200 250 >250 Information on other output voltages and output current over 250A available on request. Type example: 24TPR50 = TPR 24V/50A CABINETS Wall mounted and floor standing cabinets available depending on system rating and options specified. Weights and dimensions on request. Also available: • Dual system in single cabinet • Battery integrated in system cabinet • Matching battery cabinets >> Industrial Chargers and DC Systems FEATURES • Rectifier output current • Load DC voltage Metering • AC mains voltage (Average Voltage) • Rectifier output voltage Controls • Rectifier failure trip • High DC voltage trip • Mains failure trip
Alarms • High charge voltage battery • Low charge voltage battery • Rectifier failure • High rectifier current • High DC load voltage • Low DC load voltage • AC voltage high and low (mains failure) • Earth fault + / earth fault - • Over temperature trip (only in case of forced-air cooling) • Alarm reset • Adjustment of alarm levels Available customisation features for the high rate charge • Manual • Automatic: 0 to 99h • Periodic: 1 month, 6 months or 12 months • Commissioning charge • Current limitation for commissioning charge Available customisation features for the alarms • Latch (display alarm and/or relay outputs) • Adjustable alarm time delays Monitoring • High rate charge time remaining • List of current alarms • History of up to 200 events OPTIONS To provide exact solutions for each application, Saft power systems offers a wide range of options: • Remote alarm • Battery temperature compensation • Manual adjustment of voltage and/or current (limited to non-battery systems) • Interior light • High DC voltage trip • End of discharge contactor • Input MCB / fuse / switch or contactor • Battery MCB fuse / switch • Load MCB / fuse / switch • Analog meters in front panel • Blocking diode for parallel redundancy • Cabinet heater • Fuse / MCB trip alarm • High ripple voltage alarm • 24V and 48V telecom filter • Diode dropper • Audible alarm • Low electrolyte level • Protection: - External cabinet: up to IP65 - External wall-mounted cabinet: IP41 - Open-door cabinet: IP20 • Interior single-phase 16 A max AC outlet • LED indicators in front panel • Remote voltage sensing (battery) • Battery room fan control during high rate charge • Four multifunction digital inputs are available, for example: - Low electrolyte level - High ripple voltage - Battery symmetry fault - Diode dropper fault - Fuse/ circuit breaker trip - Free programmable text • Five inputs for specific controls • Over temperature trip (Only in case of forced ventilation) • Monitoring: - Stored and time-stamped history of events • Communication galvanically isolated RS232C • Remote surveillance and control software (sparc) • Battery/ load current measurement • Special treatment (Tropicalization, relative humidity up to 95%, etc) • Low smoke wiring (halogen-free) • Special markings • Customised cabinets (paints, etc.) • Mains change-over switch • Special types of fuses • Door mounted on/off switch • 12 Pulse control • Protocol convertor (Byte-bus, J-bus) • Battery fuse box • Other options on request • EMC filtering >>
Page 1 and 2: Industrial Chargers and DC Systems
Page 3: Current regulation ± 1% to I max L

IndustrIal Chargers and dC systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?