download - LENS

STANDARDIZED SUFFIXES
ORDERING INFORMATION
A
Standardized Suffixes (Standard Code 1)
Insulator Contact Chrome Guide
Material Termin. Plating Mark
PTFE
PBT
solder
solder
crimp
Standard
Strain Relief Color for Cable Connectors
White Black Green Blue Yellow Red Grey
DBP, DBPE,
DBPU with
solder contacts
natural red -60 -61 -62 -63 -64 -65 -66 -67 -69
black white -70 -71 -72 -73 -74 -75 -76 -77 -79
natural red -80 -81 -82 -83 -84 -85 -86 -87 -89
black white -90 -91 -92 -93 -94 -95 -96 -97 -99
natural red -100 -101 -102 -103 -104 -105 -106 -107 —
black white -110 -111 -112 -113 -114 -115 -116 -117 —
matt — -120 -121 -122 -123 -124 -125 -126 -127 -129
natural red -130 -131 -132 -133 -134 -135 -136 -137 -139
solder
PEEK black white -140 -141 -142 -143 -144 -145 -146 -147 -149
natural red -150 -151 -152 -153 -154 -155 -156 -157 —
crimp
black white -160 -161 -162 -163 -164 -165 -166 -167 —
Clamp Set Distribution Guide for Cable Connectors
Series Multipole and Triax Connectors Coax , Mixed and High Voltage Connectors
101 S, K, DK - Clamp sets are included S, K, DK - Clamp sets are included
102
103
1031
104
105
106
107
}
S, SA, SC, SV,
SOV, WS,
Clamp sets should be ordered
WSE, WSO, separately, selected from
K, DK, DKBE pages H1 - H7 and H9 - H10
KE, DKE
Clamp sets are included, but clamp diameter
should be added to the connector part number,
separated by a ‘/ ‘
Mixed coax and high voltage connectors are listed
on page H8.
The following list describes the different types of clamp systems available:
Type «S»
Type «U»
Type «E»
for Shielded cable, when the shield is to be terminated to the connector body.
Shielded clamps can also be used for unshielded cable.
for Unshielded cable, or where the shield is not to be terminated to the connector body.
These clamps are available for series 102 through 105 and are slightly easier to assemble
as there is only one piece instead of three.
for Environmental applications, where the interface between cable and connector body must be
sealed. This type of clamp can be used for both shielded and unshielded cables.
Part number examples for Multipole and Triax:
Plug S 104 A056-130 for cable of diameter 6.7mm
Shielded: Plug: S 104 A056-130+
Cable clamp: E3 104.3 / 6.7 + B
Unshielded: Plug: S 104 A056-130+
Cable clamp: E3 104.6 / 6.7
Sealed: Plug: S 104 A056-130+
Cable clamp: E3 104.2 / 6.7 + B
Part number examples for coax connectors ofall Series:
(For mixed contact connectors see page H8)
S 102 A017 / 4.7
SE 102 A017 / 4.3
For non-sealed coax connectors, the diameters are selected
from the tables for shielded clamps «S» and for sealed coax
connectors from the tables «E» on pages H1 - H7
3