Counters, Panel Meters, Tachometers and Timers

More documents

Recommendations

Info

54.1 Counters, Panel Meters, Tachometers and Timers Totalizers 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 Technical Data and Specifications General Specifications Description Figures Speed Rotation direction Ratio Shaft Drive Bearings Figure size Finish Reset Dimensions Approximate Dimensions in Inches (mm) D-7 Series 0.50 (12.7) 1.51 (38.5) 1.92 (48.8) 2.53 (64.3) 0.75 (19.0) Specification 5 standard Up to 800 cpm in 1:1 ratio Clockwise or anti-clockwise when viewed from right-hand end of counter 1:1 standard 0.31 in (7.9 mm) diameter stainless steel; 0.66 in (16.7 mm) right-hand drive, 0.63 in (15.9 mm) left-hand drive Right- or left-hand spur gear drive Oil-less, maintenance free 1/4 in (6.4 mm) high, black-on-white background Black frame and cover Wing nut or non-reset 0.12 (3.2) 0.78 (19.8) Dia. 0.31 (7.9) 0.50 (12.7) Dia. 0.120 (3.05) 4 Mtg. Holes 1.17 (29.8) 1.62 (41.3) 1.72 (43.6) 20 Control Products Catalog CA08102001E—August 2010 www.eaton.com
Counters, Panel Meters, Tachometers and Timers Totalizers 54.1 D-6 Series—Durant ® Product Description Model D-6 right-angle worm drive counters are ruggedly designed for high speeds on light-duty applications. Small “D” counters are easily Product Selection When Ordering Specify To determine a model number from the Product Selection table for Model D-6 D-6 Series Revolution Counter adapted as accessory equipment on machinery where right-angle drive is desired to permit full view reading of the counter. Series Revolution Counters, consider: ● Shaft rotation direction D-6 Series Revolution Counters No. of Figures Drive Rotation Reset Mounting Catalog Number Top View of Counter Notes When shaft is turned in the reverse direction of rotation, the counter will subtract. Top view of counter—anti-clockwise shaft rotation. Top view of counter—clockwise shaft rotation. Special feature: Measuring wheels and brackets available for lineal measurement in feet. Special feature: Measuring wheels and brackets available for lineal measurement in yards and 1/8ths. Special feature: Measuring wheels and brackets available for lineal measurement in yards. Order Number 5 Front and rear Anti-clockwise Wing nut Base 5-D-6-1-AC 31052401 6 Front and rear Anti-clockwise Wing nut Base 6-D-6-1-AC 31052402 5 Front and rear Clockwise Wing nut Base 5-D-6-1-CL 31052404 6 Front and rear Clockwise Wing nut Base 6-D-6-1-CL 31052405 5 Front and rear Anti-clockwise Wing nut Base 5-D-8-1-AC 40187401 6 Front and rear Anti-clockwise Wing nut Base 6-D-8-1-AC 40187402 5 Front and rear Clockwise Wing nut Base 5-D-8-1-CL 40187417 6 Front and rear Clockwise Wing nut Base 6-D-8-1-CL 40187418 5 Front and rear Clockwise Wing nut Base 5-D-9-1-CL 40187404 5 Front and rear Anti-clockwise Wing nut Base 5-D-9-1-AC 40187410 5 Front and rear Clockwise Wing nut Base 5-D-90-1-CL 40187414 5 Front and rear Anti-clockwise Wing nut Base 5-D-90-1-AC 40187408 Anti-Clockwise Shaft Rotation Clockwise Shaft Rotation 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 Control Products Catalog CA08102001E—August 2010 www.eaton.com 21
Page 1 and 2: Counters, Panel Meters, Tachometers
Page 19: Counters, Panel Meters, Tachometers
Page 71 and 72:
Counters, Panel Meters, Tachometers
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
show all

Counters, Panel Meters, Tachometers and Timers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?