SPANNTOP
SPANNTOP
SPANNTOP
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
MANDO Adapt. Mandrel-in-<strong>SPANNTOP</strong>-chuck<br />
set-up without alignment<br />
draw bolt<br />
Mandrel size<br />
Chuck size<br />
Clamping range<br />
of the mandrel<br />
[mm]<br />
Span [mm]<br />
This mandrel-in-chuck offers convincing performance,<br />
long-lasting power, and unusual speed. It is unsurpassed<br />
by any jaw chuck. In terms of the time savings<br />
offered by the MANDO Adapt, they do not even<br />
come close. A top-class internal clamping fixture.<br />
The advantages<br />
■ change from O.D. clamping to I.D. clamping in<br />
less than 2 minutes – without taking the chuck off<br />
the machine<br />
■ high attainable concentricity without alignment<br />
[< 0.005 mm]<br />
■ five different mandrel sizes – each available for<br />
chuck sizes 42 – 100<br />
0<br />
1<br />
2<br />
3<br />
4<br />
42<br />
52<br />
65<br />
80<br />
100<br />
42<br />
52<br />
65<br />
80<br />
100<br />
42<br />
52<br />
65<br />
80<br />
100<br />
65<br />
80<br />
100<br />
65<br />
80<br />
100<br />
ø 20 - 28<br />
ø 20 - 28<br />
ø 20 - 28<br />
ø 20 - 28<br />
ø 20 - 28<br />
ø 26 - 38<br />
ø 26 - 38<br />
ø 26 - 38<br />
ø 26 - 38<br />
ø 26 - 38<br />
ø 36 - 54<br />
ø 36 - 54<br />
ø 36 - 54<br />
ø 36 - 54<br />
ø 36 - 54<br />
ø 50 - 80<br />
ø 50 - 80<br />
ø 50 - 80<br />
ø 70 - 100<br />
ø 70 - 100<br />
ø 70 - 100<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.25<br />
± 0.35<br />
± 0.35<br />
± 0.35<br />
± 0.40<br />
± 0.40<br />
± 0.40<br />
Fast and easy change-over<br />
Remove clamping head Install MANDO Adapt Mount segment bushing Screw in draw-bolt Mount the end-stop blank<br />
Mount MANDO Adapt on the front side of the <strong>SPANNTOP</strong><br />
chuck and you are ready to go. The mandrel is then adapted<br />
with < 0.005 mm runout. When the draw bolt that is needed<br />
for the actuation of the segmented bushing is screwed on, a<br />
slick mechanism will spread and adapt to the coupling that<br />
normally grabs the clamping head.<br />
14 MANDO Adapt . Mandrel-in-<strong>SPANNTOP</strong>-chuck