P1224 Series Wall‑mount Field‑selectable Horn Strobes

2 | P1224 Series Wall‐mount Field‐selectable Horn Strobes
When used in applications requiring the appliance to be
weather‐proof or outdoor listed, the P1224MCK model
must be used. It must be installed to the SSWBB
Weatherproof Back Box using the supplied mounting plate
and gasket.
Indoor Applications
These horn strobes are equipped with a mounting plate that
can be mounted to the indicated back boxes for the
indicated applications:
Conduit
Applications
Surface
Mounted
Flush
Mounted
Single‐gang • 1
four‐inch square • • 2 •
1 Flush mounting on a single‐gang box requires using an
SSS‐MP Small Footprint Mounting Plate.
2 Surface mounting on a four‐inch square back box requires
the use of a surface mount back box skirt (SSBBS or
SSBBSW).
Strobe Cautions
Do not exceed:
• The voltage range for the chosen nominal voltage (8 V
to 17.5 V for 12 V nominal or 16 V to 33 V for 24 V
nominal)
• 70 strobes and a maximum line impedance of 4 Ω per
loop when using a synchronization module
• The maximum line impedance of the control panel
Wiring
Note
These strobe units are not recommended for
use in coded or pulsed signaling circuits.
The input terminals accept wires with diameters between
18 AWG (1.2 mm) and 12 AWG (2.3 mm).
Parts Included
Quant.
Component
1 P1224 Horn Strobe
1 SSD‐MP Universal Mounting Plate
1 Hardware pack
1 Literature pack
Technical Specifications
Environmental Considerations
Mechanical Properties
Candela Selections: 15 cd 1 , 15/75 cd 1 , 30 cd 2 , 75 cd 2 ,
or 110 cd 2
Dimensions (HxWxD)
with universal plate:
Dimensions (HxWxD)
with small footprint plate:
Horn Audibility
(UL Reverberant Room)
at 10 ft (3 m):
Material:
Weight without mounting plate:
5.6 in. x 5 in. x 2.9 in.
(14.3 cm x 12.7 cm x 7.5 cm)
5.6 in. x 3.4 in. x 2.3 in.
(14.3 cm x 8.6 cm x 5.9 cm)
75 dBA
Molded plastic enclosure incorporating
a Xenon flashtube.
8.8 oz. (0.25 kg)
1 When set at these settings (15 cd or 15/75 cd) the devices
automatically work on both 12 V and 24 V power supplies.
The 15/75 cd selection is listed at 15 cd per UL1971 but
provides 75 cd on axis.
2 The strobe is not listed for 12 V operating voltages when
set to these selections (30 cd, 75 cd, and 110 cd). When
using a 12 V control panel, this device yields required light
output only in the 15 cd and 15/75 cd settings.
Power Requirements
Maximum Operating Horn Current
(12 VDC):
Maximum Operating Horn Current
(12 VFWR):
Maximum Operating Horn Current
(24 VDC):
Maximum Operating Horn Current
(24 VFWR):
Maximum Operating Strobe Current
(12 VDC):
Maximum Operating Strobe Current
(12 VFWR):
Maximum Operating Strobe Current
(24 VDC):
Maximum Operating Strobe Current
(24 VFWR):
Voltage (Nominal Input):
57 mA RMS
57.58 mA RMS
44.4 mA RMS
45.7 mA RMS
15 cd: 127 mA RMS
15/75 cd: 27 mA RMS
15 cd: 112 mA RMS
15/75 cd: 135 mA RMS
15 cd: 59 mA RMS
15/75 cd: 9 mA RMS
30 cd: 90 mA RMS
75 cd: 160 mA RMS
110 cd: 209 mA RMS
15 cd: 64 mA RMS
15/75 cd: 4 mA RMS
30 cd: 93 mA RMS
110 cd: 08 mA RMS
12 VDC or FWR unfiltered or
24 VDC or FWR unfiltered
Voltage (Operating Range): 12 V: 9.5 V to 17.5 V;
24 V: 16 V to 33 V
Relative Humidity:
Temperature (operating):
Up to 95%, non‐condensing
Indoor use: +32°F to +120°F
(0°C to +49°C)
Outdoor use: +32°F to +150°F
(0°C to +66°C)
Trademarks
QuickClick and Sync•Circuit are trademarks of System Sensor® in the
United States and other countries.
System Sensor® is a registered trademark or a trademark of Pittway International,
Ltd. in the United States and other countries.