Catalog
Catalog
Catalog
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
60 AMP PLUGGABLE CONNECTOR<br />
603RAH or 603STH:<br />
Right-Angle or<br />
Straight Header<br />
Patented High<br />
Current/Minimal<br />
Loss Design<br />
Up to 6 Gauge Wire<br />
Reversible<br />
Connector Cover<br />
Standard<br />
Footprint<br />
on PCB<br />
Alternative Wire Ports<br />
603RAC: Right-Angle Connector<br />
Exclusive Perma-Lock <br />
terminals virtual eliminate<br />
loose terminal screws.<br />
L<br />
New connection system allows for 10<br />
times faster swap-out of printed circuit<br />
boards compared to “hard-wired”<br />
terminal block connectors.<br />
The new Marinco ® 603 Pluggable Connection<br />
System is the first 60-amp power interconnect<br />
to replace traditional terminal blocks, which<br />
require time-consuming wire preparation,<br />
including wire stripping and crimping by a<br />
certified electrician.<br />
The interconnect system is a drop-in replacement<br />
for terminal block connections, and it<br />
fulfills Bellcore’s 60-amp limit for power<br />
conducted by single cable to a switch. Using<br />
the 603 system, technicians can replace PCB<br />
power boards in about 3 minutes, compared<br />
to up to 30 minutes for an electrician rewiring<br />
a traditional terminal block.<br />
The 603RAH is the Right-Angle Header component<br />
that mounts directly onto the PCB,<br />
using the same footprint as a standard<br />
terminal block. The Header is also available<br />
in a Straight-Mount configuration, the<br />
603STH. Each Header has three, industrystandard<br />
.550 centerline-spaced pins that<br />
interconnect with the female 603RAC<br />
Right-Angle Connector component.<br />
The 3-wire Connector accepts up to 6-gauge<br />
wire and has two sets of terminal entries: by<br />
removing two holding screws, the<br />
Connector’s cover can be detached, allowing<br />
the installer to insert the three wires into either<br />
the top or the bottom side of the Connector,<br />
depending upon the end-user’s preference<br />
and space considerations.<br />
The Connector itself can only mate with<br />
the Header’s pins in one orientation,<br />
making it impossible for technicians to<br />
plug it in the “wrong way.”<br />
The heart of the system is the patented<br />
Radsok ® Hyperbolic Cylinder. As a male pin<br />
is inserted in the gun barrel-like cylinder, the<br />
cylinder’s grid deflects, imparting high normal<br />
forces. The hyperbolic grid design ensures<br />
minimal voltage loss and joule heating, at the<br />
same time making it very easy to insert the<br />
pins into the Connector (low-insertion force).<br />
The cylinders are very rugged, allowing for<br />
repeated insertions and off-axis insertions.<br />
60 AMP PLUGGABLE CONNECTOR<br />
AMPERAGE POLES/ VOLTAGE RIGHT ANGLE STRAIGHT RIGHT ANGLE<br />
WIRES HEADER MOUNT CONNECTOR<br />
HEADER<br />
60 2P 3W 50V DC 603RAH 603STH 603RAC<br />
Bagged combinations:<br />
603RCH: Right-angle header<br />
(603RAH) and right-angle connector<br />
(603RAC) in one bag.<br />
603SCH: Straight-mount header<br />
(603STH) and right-angle connector<br />
(603RAC) in one bag.<br />
DETAILED<br />
SPEC<br />
SHEETS<br />
ON-LINE<br />
www.marinco.com<br />
36<br />
Tel: 800-767-8541 Fax: 707-226-9670 www.guestindustrial.com