pdf File - Ellett Brothers

674
Motor Accessories
Trolling
Motors
Audio/
Instruments
Depth
Finders/GPS
Vests/
Cushions
Water
Sports
Safety/
Optics
Boat
Access.
Mooring/
Docking
Hardware
Lighting
Boat Seats
T & R MARINE
TRANSOM PLATE
Holds small outboard on transom securely. Prevents damage to transom
by clamps. Plated-aluminum for maximum corrosion-resistance.
Drilled for mounting screws. Dimensions: 4"H x 10"L.
Order # Mfg. # Sugg.Ret.
6201644 TP-32 $38.99
T & R MARINE
TRANSOM PROTECTOR
2-piece plated aluminum. Fits all transoms; protects
& strengthens. Easy to install; prevents
mounting bolts from working into transom.
Order # Mfg. # Sugg.Ret.
6201643 TP-30 $100.99
TRANSOM WEDGES &
SETBACKS & ELEVATORS
T-H MARINE
TRANSOM SPACERS
Aluminum spacers with four 4-1/2" SS
mounting bolts. Adds 2" setback to jack plate. Standard 4-bolt pattern.
Order # Mfg. # Sugg.Ret.
6208325 TS-1-DP $127.99
T & R MARINE
TRANSOM ELEVATOR
Aluminum construction. Allows long shaft engine to
be used on short shaft boat transoms. Raises engine
5". For all clamp-on engines up to 40 HP.
Order # Mfg. # Fits Transom Sugg.Ret.
6201640 TE-217 1-3/4" thick $228.99
6201641 TE-218 2" thick 228.99
JACKPLATES
CMC
BA-130 BREAK AWAY
For use in shallow, stumpy areas. Allows
small boats and motors to slide
over submerged logs or debris at low
speeds. Rated for outboard motors up
to a maximum of 130 H.P. Mount between the transom and outboard
motor. Helps minimize damage only while running at speeds under 5
MPH in the forward direction. Momentum causes the motor to deflect
and rotate 45º to slide over obstructions. A drawbar spring in the unit
helps return the motor to its normal position. The drawbar spring also
holds the motor at the normal position while operating in the reverse
direction at low RPM. Unit is not designed to encounter obstructions
while the boat is being operated in the reverse direction. Pre-drilled
with the standard BIA bolt pattern. For motors that have clamps w/
thumb screws, CMC part #13022 Transom Clamp Adapter is required.
Order # Mfg. # Sugg.Ret.
6216413 13003 $472.99
Boat Covers
Fuel
Trailers/
ATV Access.
Pumps
Electrical
Maintenance
Controls/
Steering
Motor
Access.
Camping
Cutlery
T-H MARINE
REVERSE TRANSOM WEDGE
Gains more "Bow Up". Provides 5º positive tilt.
Rugged cast aluminum.
Order # Mfg. # Sugg.Ret
6032111 TW-3-DP $44.99
T-H MARINE
TRANSOM WEDGE
Fits all standard 4-bolt patterns. Full contact between
engine & transom. Adds 5º of tuck to transom
angle. 2-1/4''Wx11-1/4''L - 1-16'' to 3/16'' thick.
Order # Mfg. # Sugg.Ret.
6201167 TW-2-DP $40.99
T & R MARINE
TRANSOM WEDGE
5º cast aluminum. For boats with insufficient
transom angle or boats with planing
problems at low speed. Individual mounting
holes. For: Johnson-Evinrude-all bolt-on models 1973 & newer;
Mercury-Black Max V-6 1980 & newer & 90-115 HP 1984 & newer,
Suzuki-50-60-115-140 HP 1981 & newer; 150-150SS-200 HP 1986 &
newer, Yamaha-115-220 HP 1984 & newer. Sold in pairs.
Order # Mfg. # Sugg.Ret.
6201638 TW50 $53.99
CMC
PL-65 HIGH SPEED
HYDRAULIC JACK PLATE
Made of 3/4'' & 1/2'' 6061 T6 alloy aluminum
extrusions and fastened w/SS fasteners. Ideal
for fresh or saltwater use. No welds or castings
to break. Dependable self contained and
water proof high speed hydraulic actuator has
a max. lifting capacity of 4417 pounds of thrust.
You will have no problem lifting even a V-6 300
hp max. motor at full throttle. The hydraulic actuator
is mounted inside the structure of the Power-Lift, yet it is fully
accessible without removing the engine. There are no hoses to contain,
nor will you have to contend with mounting a pump and reservoir
inside your boat, as is the need with other transom jacks. The hydraulic
actuator is completely self-contained with its own fluid reservoir
(eliminates the need for hydraulic tank and hoses inside the boat).
It contains a permanent magnet motor for more power and constant
torque. The cylinder within the actuator has more lifting capacity than
other transom jacks on the market. It contains a no-leak seal and
wiper that keeps dirt and water out of the working parts. The system
is made of 100% non-ferrous material which makes it impervious to
saltwater and freshwater. The patented roller design means less friction,
longer wear, less maintenance, and virtually no binding problems
which are common with other transom jacks. The roller assembly contains
a stainless steel 3/4" pin with aluminum-bronze alloy rollers. The
roller is highly impact-resistant, corrosive-resistant, and has a high
load carrying capacity. This patented design virtually eliminates any
chance of binding which is common with other transom jacks. The PL-
65 HS is rated for V-6 motors and smaller and gives you 5" of vertical
travel with 1-1/2" of adjustment on the motor bracket and 1-1/2" of adjustment
on the transom bracket. A total of 8" of possible adjustment.
Order # Mfg. # Type Sugg.Ret.
6216907 65301 With Gauge $1133.99
6216884 65302 Without Gauge 916.99