Sinergroup Water Filters Reverse Osmosis water Softeners

* Temperature Min: 4°C
* Temperature Max: 35°C
* Inlet/Outlet water 1" M. (30lt.), 3/4" M. (6,12,12.5, 15, 18lt.)
Water hardness (limestone)
In °F (French degrees), can be measured with the drops of Titrant, iportant to determine the choice of the
type of water softener and optimize the consumption of salt.
Ability to interchange
Hardness of the water softener is able to hold.
6 resin liter: 19ºHFxm3 * 12 resin Liters: 49ºHFxm3 * 12.5 resin Liters: 49ºHFxm3 * 15 resin Liters:
75ºHFxm3 * 18 resin Liters: 97ºHFxm3 * 30 resin Liters: 170ºHFxm3.
Sample calculation to determine the correct article
A water softner of 30 liter resin with a hardness of 40°F (medium-high hardness), develops 4.250liters of
softened water (170:40 = 4.250). In this case, must planning 4.2m3 in treatment capacity of the softener
through the buttons on the display and provides free water softener without scale at zero French degrees.
Adjustment of the hardness out
It's recommended to not leak totally softened water in a residential installation. Dayton Water softeners
have a residual hardness integrated regulator that allows you to precisely adjust the hardness of the treated
water. To adjust the residual hardness must then carefully open the regulator MIX valve. All softeners are
supplied with the valve fully closed and then will deliver water at 0°F. Water intended for human
consumption, we recommend a residual hardness between 5 and 10ºF for copper pipes and between 8 and
10 º F for iron pipes. Depending on the hardness out planned, the water softener will tend to produce more
water and less sweetened salt intake because the input hardness must be compensated with the output
value. A water softner of 30 liter resin with a hardness of incoming 40°F and 5°F and out of hardness,
develops 4.857lit. of softened water (170:35=4.857). In this case must planning 4.9 m3 in treatment
capacity of the softener through the buttons on the display. The average every person consumes 150 liters
of water a day is recommended and a regeneration time scheduled every 4/5 days, then a family of 4 with
water at 40°F consumes x5 days 3.000 liters, a 30 liters of water softner so with a planned regeneration
even at 6 days can be installed.
Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents the
formation of deposits in pipes and hydraulic lines. Greater sense of wellness during the shower. Skin soft
and clean. Increased duration of appliances and boilers. COST SAVING: reduction in the use of soaps,
fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry
about adding salt in the water softner.
Increased sodium (for drinking water)
Most of the sodium consumed is taken with food, especially those produced by industrial processing. Salt is
an excellent preservative and is used as an additive for processed products. The intake of sodium with the
water we drink is relatively low compared to that which is taken with food. All softeners to produce soft
water using ion exchange resins in the produce softened water output of sodium ions. The recommended
sodium limit for water intended for human consumption is 200 liters ppm. Depending on the concentration
of sodium and water hardness, the water can have a concentration of sodium than the recommended.
Where this occurs, or if you need to follow a diet low in salt, it is advisable to install a reverse osmosis
drinking water for the home.
Specifications Model 15000106-01 6lt. resin. (ideal for one person)
* Regeneration salt consumption: 0,48 kg/salt.
* Water consumption for regeneration: 30lt.
* Number treated water for regeneration, 35°F-0,542m3, 40°F-0,475m3, 45°F-0,422m3, 50°F-0,38m3,
60°F-0,316m3.
* Working flow m3/h 0,24.
* Working flow m3/h MAX 0,36.
* Dimensions in cm (HxWxD) 46,5x20x36
07 February 2015 32/359