UK manufacturing recovery gathers pace - Capsule-group.com

More documents

Recommendations

Info

MAINTENANCE MATTERS PROBLEM SOLVER TROUBLE SHOOTER The answer to this month’s Trouble Shooter is provided by Parker Pneumatics QHow do I size the correct filtration for my pneumatic system AWith as many as 90% of all pneumatic system failures attributable to the poor quality of the air supply, ensuring you have an effective air preparation solution in place is key to both productivity and safety. The purification technology you require will depend on the type of contaminants present in your compressed air system. A water separator can help remove bulk condensed water; a dryer may be necessary to expel water vapour; and various filters can be fitted to remove water aerosols, atmospheric dirt and solid particles, micro-organisms, oil vapour, liquid oil and oil aerosols, and rust and pipescale. Modular FRL systems are now available to help you build a bespoke air treatment system. The size of these different air preparation systems should be specified in relation to the flow of compressed air needed to drive downstream equipment, and the acceptable pressure drop across the system. In terms of filtration, vortex type filters require a pressure drop of around 0.2 to 0.3 bar to ensure contaminants are removed effectively, while element type filters are able to work more successfully with lower pressure drops. If the filtration system is over specified and the pressure drop too high, excess strain will be put on the compressor, driving up energy costs and reducing the performance of pneumatic equipment. Routinely replacing filter elements is essential to prevent media becoming saturated and the pressure drop increasing, adversely affecting productivity. 14 JUNE 2010 PLANT&WORKSENGINEERING When Prelok encountered problems using both impeller and diaphragm pumps to circulate adhesive coating fluids at its Willenhall plant in the West Midlands, this specialist in the application of preapplied locking and sealing processes for threaded components, turned to 521 Series pumps from Watson-Marlow. Used in combination with Gore Style 400 high resilience tubing, the solution overcame problems caused by previous pumps of damaging the fluid, or of the fluid damaging the pump. Prelok provides a range of high specification pre-applied thread locking and sealing products that are used throughout the automotive, IT, construction and telecommunications sectors. “Our strengths lie in our ability to help customers source or manufacture quality components, quickly processing them and providing logistic solutions”, says Andy Jones, site services manager and maintenance co-ordinator at the 75-employee company. He added: “When we have a problem in production we apply all of our energies into finding a rapid and suitable solution.” One such problem involved a process that re-circulates adhesive coating fluids prior to application. These fluids can be water- or solvent-based with the exact makeup dependent upon customer requirements. “The problem focused on micro capsules that are suspended in the adhesive coating fluid”, explains Jones. “We found that the impellor type pumps damaged the capsules, while a subsequently installed diaphragm pump could not work with the sometimes small amount of fluid that is present. Furthermore it was hard to get the specific diaphragm material which is resistant to some of the aggressive chemicals we use.” Fortunately Jones recalled using Watson-Marlow peristaltic technology successfully in another process. In peristaltic pumping operations, nothing but the hose or tube touches the fluid, eliminating When Prelok encountered problems using both impeller and diaphragm pumps to circulate adhesive coating fluids the company turned to 521 Series pumps from Watson-Marlow Robust pump and tube combination solves sticky situation the risk of the pump contaminating the fluid, or the fluid contaminating the pump. Fluid is drawn into the pump, trapped between two rollers and expelled. The complete closure of the tube gives the pump its positive displacement action, preventing backflow and eliminating the need for check valves when the pump is not running. A Watson-Marlow 521 Series pump was duly installed at Prelok’s Willenhall factory where it successfully overcame the previous problems encountered. So impressive was its performance that the company now has a total of four 521 Series pumps at Willenhall, with a further four dotted across its European operations. All of the units utilise an inverter to control speed, and all run continuously throughout the entire production period. Despite this demanding workload Jones says that maintenance tasks extend to no more than “spraying some lubricant on the rollers and springs every now and again”. One final problem remained, however. The aggressive nature of some of the chemicals used within Prelok’s adhesive coating fluids meant that the Marprene and Tygon tubing deployed initially exhibited short working life leading to short life and sometime ruptured tubes. Jones commented: “Since switching to the Watson-Marlow peristaltic pumps this at least meant it was easier to clean and get the process up and running again, however, it was still an issue we needed to resolve.” He added: “I contacted Watson Marlow about alternative tube materials and our local sales engineer sent me a sample pack of different tubing material for me to immerse in our fluid to test. He followed up with a site visit and suggested we use a new type of pumphead (with quick release couplings) and Gore Style 400 tubing to trial. So far we haven’t had a tubing rupture in the months it has been running.” While chemicals will attack most other types of tubing, the secret behind the resilience of GORE Style 400 is Viton GF-600S, a peroxidecured fluoroelastomer based on DuPont advanced polymer architecture. Performance testing shows that Style 400 tubing offers greater than 50 times longer life than conventional non-reinforced extruded tube. Thanks to its expanded PTFE reinforcement, the new tubing also offers superior burst resistance to protect against the swelling effect produced when pumping aggressive chemicals using standard extruded tube. ■ For further information please visit: www.wmpg.co.uk
Dust and fume �� extraction hoses �� from Masterflex �� ● Temperature range -260°C to +1100°C � �� ● Size range 38 mm to 900 mm �� ● Very flexible, small bend radius �� ● Long service life, low operating costs � �� ● Suitable installation and connecting systems �� Masterflex Technical Hoses Ltd �� GB-Oldham OL1 4ER �� Tel: 0161 626 8066 �� www.masterflex-uk.com �� PU / FABRIC HOSES CONNECTIONS TUBE PROTECTION Register for a FREE roadshow near you! FREE FULL TRIAL. NO RISK! � Access from anywhere � Information at a glance � Fits like a glove � Sure road to success � Why pay more? CMMS Take control! Increase uptime, reduce costs, enforce compliance and prove due diligence. To find out more, visit us online. Call today +44 (0)23 8022 4111 info@shiresystems.co.uk BROWSER BASED It’s child’s play! shiresystems.co.uk 10 000+ customers Page 1 ��
Page 1: Pay freezes thaw The continued emer
Page 4 and 5: We Make Protecting People Our Busin
Page 6 and 7: NEWS UK manufacturing recovery gath
Page 8 and 9: PLANT EXTRA BCAS’ monthly column
Page 10 and 11: CONDITION MONITORING Sentry G3 from
Page 12 and 13: Make complex stuff simple. Reduce M
Page 16 and 17: IF ALL BOILERS WERE THIS EFFICIENT
Page 18: PROCESS, CONTROLS, & PLANT can addr
Page 21 and 22: Focus on: Seals, Bearings, & Lubric
Page 23 and 24: PARTNERSHIP BASED ON TRUST - AND TR
Page 25 and 26: educe energy consumption. Unfairly,
Page 27 and 28: Premises cleaning Works canteens ki
Page 29 and 30: Solutions by KIMBERLY-CLARK PROFESS
Page 31 and 32: ��
Page 33 and 34: Please call for a FREE demonstratio
Page 35 and 36: HANDLING & STORAGE Focus on: Forkli
Page 37 and 38: In Britain some 170,000 people suff
Page 39 and 40: Call: 0121 248 2233 Email: enquirie
Page 41 and 42: leslah@dfamedia.co.uk Spotlight FAS
Page 43 and 44: leslah@dfamedia.co.uk Spotlight FLU
Page 45 and 46: leslah@dfamedia.co.uk Spotlight THE
Page 47 and 48: PRODUCTS AND SERVICES DIRECTORY BOI
Page 49 and 50: PRODUCTS AND SERVICES DIRECTORY LUB
Page 51 and 52: PRODUCTS AND SERVICES DIRECTORY TRA
Page 53: QUAD-POWER ® III THE ULTIMATE IN V

UK manufacturing recovery gathers pace - Capsule-group.com

Create successful ePaper yourself

Delete template?

Save as template?