Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>HYDRAULIC</strong> ROLLER <strong>CAMSHAFTS</strong><br />
1965-1996<br />
366 396 402 427 454 502 & Rodeck V8 Big Block<br />
Note: These cams use .000" intake and exhaust valve lash.<br />
Chevrolet<br />
C.I.D.<br />
Group<br />
Low<br />
RPM<br />
RPM Range<br />
Peak Peak<br />
Torque HP<br />
Top<br />
RPM<br />
396 cid 2050 3250 4500 5000<br />
402 cid 2050 3250 4500 5000<br />
427 cid 1900 3150 4400 4900<br />
454 cid 1750 2875 4125 4500<br />
502 cid 1700 2750 3950 4250<br />
Part<br />
Number<br />
01400<br />
Early model<br />
01400LM<br />
LM is step<br />
nose<br />
Lobe<br />
Center<br />
205HR213<br />
112°<br />
Advertised<br />
Duration<br />
Intake Exhaust<br />
264° 272°<br />
X-TREME MILEAGE CAMS AVAIL ABLE!<br />
CONTACT CROWER TECHNICIANS FOR MORE INFO.<br />
Duration<br />
@ .050"<br />
Intake Exhaust<br />
205° 213°<br />
Duration<br />
@ .200"<br />
Intake Exhaust<br />
110° 120°<br />
Gross Lift<br />
1.7 / 1.7<br />
Intake Exhaust<br />
.488" .512"<br />
Suitable<br />
Component<br />
Kit<br />
84579<br />
or<br />
84551LM<br />
396 cid 2250 3450 5000 5500<br />
402 cid 2250 3450 5000 5500<br />
427 cid 2150 3345 4900 5400<br />
454 cid 1950 3145 4700 5200<br />
502 cid 1850 3045 4600 5100<br />
01401<br />
Early model<br />
01401LM<br />
LM is step<br />
nose<br />
213HR222<br />
112°<br />
276°<br />
282°<br />
213°<br />
222°<br />
120°<br />
128°<br />
.512"<br />
.540"<br />
84579<br />
or<br />
84551LM<br />
396 cid 2500 3700 5300 5800<br />
402 cid 2500 3700 5300 5800<br />
427 cid 2400 3600 5200 5700<br />
454 cid 2300 3400 5000 5500<br />
502 cid 2200 3300 4900 5400<br />
01402<br />
Early model<br />
01402LM<br />
LM is step<br />
nose<br />
222HR229<br />
110°<br />
278°<br />
286°<br />
222°<br />
229°<br />
128°<br />
137°<br />
.540"<br />
.563"<br />
84579<br />
or<br />
84551LM<br />
396 cid 2750 3950 5550 6050<br />
402 cid 2750 3950 5550 6050<br />
427 cid 2650 3850 5450 5950<br />
454 cid 2450 3650 5250 5750<br />
502 cid 2330 3520 5100 5650<br />
01403<br />
Early model<br />
01403LM<br />
LM is step<br />
nose<br />
229HR237<br />
110°<br />
287°<br />
296°<br />
229°<br />
237°<br />
137°<br />
145°<br />
.563"<br />
.586"<br />
84579<br />
or<br />
84551LM<br />
Note: The above cams are ground on cast steel cores. <strong>Crower</strong> recommends using the factory stock cast iron<br />
distributor gear. If 8620 steel billet core with integral cast iron gear is desired, specify part number 00050.<br />
Note: The RPM power ranges listed above are approximations, your RPM ranges may vary depending on<br />
engine setup (cylinder head flow, etc.). “LM” cores fit 454-502 cid 1994-up only (w/step nose).<br />
Gen VI camshafts are different and require 8620 steel billet core with cast iron gear (#00050).<br />
ENGINEERED COMPONENT KITS<br />
Part No.<br />
84551<br />
84551LM<br />
Lifters Springs Retainers Plug Pushrods<br />
66321-16<br />
66331-16<br />
68340-16<br />
68340-16<br />
87063M-16<br />
87063M-16<br />
86086<br />
71755-8 & 71855-8<br />
71760-8 & 71860-8<br />
Remarks<br />
For 9.800" deck.<br />
For Late Model block.<br />
Spring pressure:<br />
68340-16 Seat: 1.900" @ 119 lbs / Nose: 1.350" @ 359 lbs / Coil bind: 1.080" ( Machine work, use cutter 68986).<br />
Note: If running a tall deck block use .400" longer pushrods. Other lengths available on a special order basis.<br />
Note: If engine is equipped with exhaust valve rotators see rotation eliminator cups (part # 68958-8).<br />
Note: For proper oiling on 1965 and 1966 engines, rear cam bearing must be grooved. Specify when<br />
ordering cam.<br />
Note: Two-gear drives and reverse engine rotation camshafts are available on a special order basis.<br />
CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full<br />
lift (minimum .050").<br />
CAUTION! For sustained running at high rpm use valve spring (68385X2-16).<br />
Valve timing events are available online at: www.crower.com/valvtime.html<br />
ACCESSORIES<br />
Part No.<br />
See pg. 180<br />
Pg's.150-165<br />
Pg's.150-165<br />
See pg.138<br />
Description<br />
Spring seat cutter<br />
Rocker arms (1.7) 7⁄16<br />
Rocker arms (1.8) 7⁄16<br />
Timing gear kit<br />
IMPORTANT! Stock big block<br />
Chevrolet single springs are designed for cams with approximately .400" lift. When<br />
stock valve springs are used with performance cams over .400" lift, coil bind and<br />
retainer to valve guide interference may occur.<br />
Note: If using longer than stock valves you may require spring and retainer<br />
modifications. See specs or contact <strong>Crower</strong>.<br />
Note: Rocker arms available in Aluminum &<br />
Stainless steel.<br />
For technical support call 619-661-6477 • Some products listed are not legal for sale or use on emission controlled motor vehicles<br />
• RPM ranges vary upon application • www.crower.com<br />
59