The K11 & K31 Manual - SwissRifles

More documents

Recommendations

Info

55, 56 1. Bolt plug 2. Cocking piece 3. Cam follower plate 4. Locking sleeve 5. Cylinder 6. Firing pin 7. Firing pin spring Fig. 24 8. Sling 17. Muzzle brake (disassembled only by a gunsmith) 9. Sling loop band 18. Round Screw 10. Sling Hook 19. Locking ring 11. Stock 20. Bolt 12. Handguard 21. Magazine 13. Magazine plate 22. Bipod 14. Receiver screws (front and rear) 23. Bipod mounting 15. Barrel 24. Scope 16. Receiver with trigger mechanism 25. Screwdriver for scope 26. Scope Case
57,58 For the scoped rifle, it is important to pay attention to the following points: Use the weapon with care to avoid impacts, wet and dirty conditions. If the scope gets wet, dry it at room temperature, not next to a heater on not in its case. The lenses should be cleaned with a clean lens cloth or a chamois. Sand particles should be removed preferably beforehand with tweezers. Metal scope parts should only be lightly oiled. The lenses should never come in contact with grease or petroleum based oils. Troops are not authorized to make repairs to the scope. Damaged scopes should be sent with the rifle to a competent arsenal. 42 Sight adjustment The weapon should be sighted in without the scope. If this is not the case, it must be adjusted with the help of a gunsmith per the gunsmith’s regulations. If the average point of impact while shooting on the bipod, Target A at 300 meters with the elevation set at 3 and windage of 0, in calm and normal conditions, is outside the black region on the target, the scope must be adjusted. Scope adjustment will be performed by the soldier to which the weapon was issued or the gunsmith. Procedure as follows: While adjusting the elevation and windage knobs during sighting in, the average impact point should be in the center of the black, with the aim point at “dead center” Next, the elevation adjustment knob should be firmly held, the screws loosened around one turn with the provided screwdriver found in the case, The scale on the knob will be set to 3 and the screws retightened. To adjust the windage, follow the same procedure, but now the scale on the knob should be placed at “0”. Fig. 26 27 Countersunk screws for adjusting elevation 28 Windage knob
Page 1 and 2: NOTES: Disclaimer: Manual readers a
Page 3 and 4: 2 Approved on order of the Federal
Page 5 and 6: 4 Table of Contents Section Part 1:
Page 7 and 8: 6 Technical Information Weapon: Rif
Page 9 and 10: 9 Fig. 1 A. Mq. Mod 31 B. Mq. Mod 1
Page 11 and 12: 11 Figure 3 B. Mq. Mod 11 A. Mq. Mo
Page 13 and 14: 13 Figure 5 Rear Sight B. Mq. Mod 1
Page 15 and 16: 16 and 17 Figure 7 B. Mq. Mod 11 I.
Page 17 and 18: 19 Figure 9 A. Mq. Mod 31 B. Mq. Mo
Page 19 and 20: 21 The cam follower pin slides in t
Page 21 and 22: 23 B. Mq. Model 11 Fig. 12 Firing M
Page 23 and 24: 25 Fig. 14 Hardware A. Mq. Model 31
Page 25 and 26: 27 Fig. 16 Accessory Pouch 1. Greas
Page 27 and 28: 29 d) Disassembly of the firing mec
Page 29 and 30: 32 and 33 b) Bolt Mq. 11 Mq. 31 Rep
Page 31 and 32: 35, 36 IV. Function 1. Trigger Mech
Page 33 and 34: 38 and 39 13 During locking sleeve
Page 35 and 36: 42, 43 and 44 VI. Weapon Maintenanc
Page 37 and 38: 46 (cont), 47 34 If a major inspect
Page 39 and 40: 50 Fig. 19 Scoped Rifle 31/42 and 3
Page 41: 53 cont, 54 Additional infor mation
Page 45 and 46: 61, 62 For this reason; one should
Page 47 and 48: 65 Fig.28 Method for gauging fie ld
Page 49 and 50: 68, 69 Part 2 Munitions I. Overview
Page 51 and 52: 72, 73 Exterior Characteristics: No
Page 53 and 54: 76, 77, 78 V. Packaging 56 The char
Page 55 and 56: 81, 82, 83 -Place the left thumb ov
Page 57 and 58: 85, 86, 87, 88 Every rifle has it
Page 59 and 60: 90, 91 Appendix I Training Figures
Page 61 and 62: 94,95 Fig. 38 Prone Position Fig. 3
Page 63 and 64: 98, 99 Fig. 42 Prone Position with
Page 65 and 66: 102, 103 Fig. 46 Shooting position
Page 67 and 68: 106, 107 Table 5 Aim Point Weapon S
Page 69 and 70: 110, 111 Appendix IV Instructions f
Page 71 and 72: 114,115 Shooting with a blocked bar
Page 73 and 74: 118, 119 Take care of your parts! I
Page 75 and 76: 122, 123 Sear adjustment Troops in
Page 77 and 78: 126, 127 3. Cleaning and greasing t
Page 79 and 80: 130, 131 Ovalization of the muzzle
Page 81 and 82: 134, 135 -Protect the rifle barrel

The K11 & K31 Manual - SwissRifles

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?