SCREW DRIVES GT, MICRONLine®, KOKON® SCREW ... - BIBUS

Screw DrivesOrder CodeBall screw drives/ball screws/KOKON ®Structure of OrderCode:Ball screw drive/ball screw1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.1. ProductKGT = Ball screw drive completeKGS = Ball screwKGF = Flanged ball nutKGM= Cylindrical ball nut2. Nut version 1)D = Version in accordance withDIN 69051N = THOMSON NEFF standard3. Nominal thread diameter [mm]4. Thread lead [mm]5. Lead accuracy50 µm/300 mm6. Thread directionRH = Right hand threadLH = Left hand thread7. Screw end 1Standard ends D, F, H, J, L, S, T, W, Zsee p. 22ffG = Annealed endK = Acc. to customer’s drawingX = Cut only8. Code for end length 1For G and K end length [mm]9. Overall length KGS [mm]10. Screw end 2Standard ends form D, F, H, J, L, S, T, W, Zsee p. 22ffG = Annealed endK = Acc. to customer’s drawingX = Cut only11. Code for end length 2For G and K end length [mm]12. Nut form and configuraton 1)Flanged side KGF nut and contact surfaceKGM nut always at screw end 1F = 1 Flanged nutM = 1 Cylindrical nutFM = 1 pre-loaded nut unit as per THOM-SON NEFF standard (1 KGF, 1 KGM)FMB= 1 Pre-loaded nut unit as perDIN 69051FF =1 Pre-loaded nut unit (2 KGF)MM =1 Pre-loaded nut unit (2 KGM)13. Sealform 1)EE = Rubber wiper (standard)OO =Without wiperZZ = 1 Wiper at each end, with location forspiral spring cover in each case14. Special version or with accessoriesO = No1 = Yes1) Not necessary for ball screwExample:1 Ball screw drive complete withmachined screw endsKGT D 20051. ProductKGT= Ball screw drive complete050 RH K105 1003 K025 F EE 01. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.6. Thread directionRH = Right hand thread11. Code for end length 2For G and K end length [mm]2. Nut versionD = Version in accordance withDIN 690513. Nominal thread diameter [mm]4. Thread lead [mm]5. Lead accuracy50 µm/300 mm7. Screw end 1K = Acc. to customer’s drawing8. Code for end length 1For G and K end length [mm]9. Overall length KGS [mm]10. Screw end 2K = Acc. to customer’s drawing12. Nut form and configurationF = 1 Flanged nut13. SealformEE = Rubber wiper (standard)14. Special version or with accessoriesO = NoExample:1 Cylindrical ball nutKGM D 2005 RH EE1. 2. 3. 4. 6. 13.1. ProductKGM = Cylindrical ball nut2. Nut versionD = Version in accordance withDIN 690513. Nominal thread diameter [mm]4. Thread lead [mm]6. Thread directionRH = Right hand thread13. SealformEE = Rubber wiper (standard)Structure of OrderCode:KOKON ®KOKON1. ProductKOKON ®401. 2. 3.2. Nominal thread diameter [mm]403. Thread lead [5/10 mm]4. Lead accuracy [µm/300 mm]5. Stroke [mm]4. 5.6. 7. 8. 9. 10.6. Overall length [mm]7. Pre-loading0 = No backlash1 = Pre-loaded8. Drive shaft0 = Without feather key groove1 = With feather key groove9. Installation positionK =Customer requirementA-D=THOMSON NEFF standard versionsInstallation position (view from fixed bearing)10. Special version or with accessories0 = No1 = YesTel : +49 (0) 7157-124- 0 Web site : www.DanaherMotion.net 61