Lee Progressive Presses and Accessories - Midsouth Shooters Supply

Rotor 0Rotor 00Rotor 01Rotor 02Rotor 03Rotor 04Rotor 05Rotor 06Rotor 07Rotor 08RCBS Powder HandlingLittle Dandy Pistol Powder Measure - Perfect for handloading pistolshooters and select small-caliber rifle shooters. There are 28 interchangeablefixed-charge powder rotors available and you can load anypopular powder with the Little Dandy in up to 400 different load combinations.There’s no readjustment needed after changeover. Can beused handheld or conventional bench-mounted tool with optionalPowder Measure Stand. Order No. 044-86040 $29.32Little Dandy Rotor Knob - Attaches to the LittleDandy Rotor with a setscrew, making the rotor easierto turn. Crafted of high strength aluminum withknurled outer surfaces for maximum finger-touchcontrol. Order No. 044-86046 $4.57Little Dandy Rotors - Fixed-charge powder rotors that loadany popular powder with the Little Dandy in up to 400 differentload combinations. (See Charge Chart Below) $8.88 eachOrder No.044-86035044-86036044-86001044-86002044-86003044-86004004-86005044-86006044-86007044-86008Rotor 09Rotor 10Rotor 11Rotor 12Rotor 13Rotor 14Rotor 15Rotor 16Rotor 17Rotor 18Order No.044-86009044-86010044-86011044-86012044-86013044-86014044-86015044-86016044-86017044-86018Little Dandy Rotor Charge ChartRotor 19Rotor 20Rotor 21Rotor 22Rotor 23Rotor 24Rotor 25Rotor 26Order No.044-86019044-86020044-86021044-86022044-86023044-86024044-86025044-86026Powder Measure/ Piggyback Stand - This stand will raise anypowder measure (with standard 7/8”–14 thread) leaving plenty ofspace for positioning a powder scale pan or cases in a loadingblock under the drop tube. Bolts easily to a reloading bench ortable. Also serves as a stand for holding a Piggyback II, -3 or -4when not in use. Order No. 044-9035 $22.88Advanced Powder Measure Stand - This stand will raise anypowder measure (with standard 7/8”–14 thread) leaving plentyof space for positioning a powder scale pan or cases in a loadingblock under the drop tube. Bolts easily to a reloading benchor table. Also serves as a stand for holding a Piggyback II, -3or -4 when not in use. Order No. 044-9092 $16.14Powder Checker - Visually check powder charges when you usea progressive press. The Powder Checker sits between the powdercharging and bullet seating stations. Probe rod lets you visuallyconfirm that the case is properly charged with powder beforebullet seating. The Powder Checker also shows low and highcharges too. Black oxide finish for contrast & better visibility. Foruse with rifle and pistol cases. Order No. 044-87590 $26.07Lock-Out Die - Detects a “no powder” or a “double charge” conditionin the progressive reloading process. It locks up, halting thetravel of the ram, alerting the reloader to the problem so thecause can be corrected. For use with straight-wall pistol calibers,9mm & larger, and only on progressive reloading presses.Order No. 044-87540 $41.37NR: No known recommended load. WARNING: The powder charge weights shown for individual rotors are to be used for general reference only. Lot to lot variations in powderdensity, temperature, humidity, operating techniques andmanufacturing tolerance all introduce variations in charge weights from the values listed. Each rotor-powder combinationused MUST be checked on an accurate scale to determine the actual charge weight prior to loading ammunition. Read and follow your measure instructions.95