Machined ring needle roller bearings - NTN-SNR: подшипники
Machined ring needle roller bearings - NTN-SNR: подшипники
Machined ring needle roller bearings - NTN-SNR: подшипники
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Machined</strong> <strong>ring</strong> <strong>needle</strong> <strong>roller</strong> bea<strong>ring</strong>s<br />
The machined <strong>ring</strong> of this bea<strong>ring</strong> type contains <strong>needle</strong><br />
<strong>roller</strong>s and a cage. The outer <strong>ring</strong> and the <strong>needle</strong> <strong>roller</strong>s<br />
are inseparable from each other due to double-side ribs<br />
on the outer <strong>ring</strong> or side plates. Its machined (solid)<br />
outer <strong>ring</strong> makes it more rigid and improves bea<strong>ring</strong><br />
accuracy. This bea<strong>ring</strong> type is suitable for an applica-<br />
Type Série RNA49<br />
Type Série NA49<br />
Série RNA49 .. Type R<br />
Série NA49 .. Type R<br />
Série Type RNA59<br />
Série Type<br />
NA59<br />
tion requi<strong>ring</strong> high speed, high load and high running<br />
accuracy. <strong>Machined</strong> <strong>ring</strong> <strong>needle</strong> <strong>roller</strong> bea<strong>ring</strong>s are<br />
available in two types – either with an inner <strong>ring</strong> or without<br />
an inner <strong>ring</strong> for applications where the shaft is used<br />
as the direct raceway surface.<br />
Applied shaft Composition<br />
Bea<strong>ring</strong> type diameter of nominal bea<strong>ring</strong> Remarks<br />
(mm) number<br />
Ø 7 � Ø 12<br />
Ø 5 � Ø9<br />
Ø 14 � Ø 490<br />
With seal<br />
Ø 14 ~ Ø 58<br />
Ø 10 � Ø 440<br />
With seal<br />
Ø 10 � Ø 50<br />
Ø 20 � Ø 160<br />
Ø 15 � Ø 140<br />
RNA 49 5 T2<br />
[Tail code]<br />
T2: Resin cage<br />
RNA 49 02 R<br />
[Tail code]<br />
R: Rib type<br />
L: Single-side seal type<br />
LL: Double-side seal type<br />
RNA 59 02<br />
NA 59 / 22<br />
Tail code<br />
Bore dia. No.<br />
Dimension series<br />
Type cod<br />
Tail code<br />
Bore dia. No.<br />
Dimension series<br />
Type cod<br />
Type No.<br />
Dimension series<br />
Type code<br />
Type No.<br />
Dimension series<br />
Type code<br />
Bea<strong>ring</strong>s with cage code T2 use a<br />
polyamide resin cage which has a peak<br />
allowable temperature of 120°C.<br />
Under continuous running conditions a<br />
temperature of 100°C or less applies.<br />
The dimension series is in compliance<br />
with JIS B 1512 or ISO 15.<br />
This type (Tail code: L or LL) has built in<br />
synthetic rubber seals on a single side or both<br />
sides and is internally filled with lithium soap<br />
based grease.<br />
The sealed bea<strong>ring</strong> type shall be used<br />
within the temperature range of -25 to<br />
100°C to prevent deterioration of the seal<br />
and grease.<br />
The dimension series is in compliance<br />
with JIS B 15 or ISO 15.<br />
The dimension series is in compliance<br />
with JIS B 1512 or ISO 15.<br />
7