PDF Catalogue - CBS Parts Ltd.

HUB-PILOTEDTUBELESS & TUBE-TYPEWHEELSACCURIDE 15° TUBELESS DUPLEX ® DISC WHEELSAluminum Hub-Piloted MountingTwo-Piece Flange Nut10-Hole, 335mm Bolt Circle, 281mm BoreULTRAMOUNT 335STUD-PILOTEDTUBELESS & TUBE-TYPEWHEELSDEMOUNTABLERIMS &COMPONENTSDUPLEX DISC®WHEELS/DUPLEX ®DEMOUNTABLE RIMSItem Wheel SizePartNumber1 22.5 x 11.75 40164ANP40164AOP2 22.5 x 11.75 40166ANP40166AOP3 22.5 x 11.75 40176ANP40176AOP4 22.5 x 11.75 40178ANP40178AOP5 22.5 x 11.75 40386ANP40386AOP6 22.5 x 11.75 40394ANP40394AOPItem7891011121314Wheel Size22.5 x 12.2522.5 x 12.2522.5 x 12.2522.5 x 12.2522.5 x 13.0022.5 x 13.0022.5 x 13.0022.5 x 13.00PartHandNumber Inset (3) Outset (3) Holes29814TK (11) ---29815TK (11)4.00"29816 4.75"29817TK (11) 5.75"2981829819TK (11)29820TK (11)28684Polish Option(TypicalApplication)MachinedOutside (Rear)MachinedOutside (Front)MachinedOutside (Front)MachinedOutside (Rear)MachinedOutside (Front)MachinedOutside (Front)---2.62"4.32"5.25"Steel Stud-Piloted Mounting (1)Outer Cap Nut10-Hole, 11¼" Bolt Circle, 8.72" Bore, .625" Disc0.63"---------0.63"---------Outset(mm)Inset(mm)BoltHole(mm)Approx.Wt. (kg)MaximumLoad(kg)MaximumInfl(bar)148 120 26 26.1 4500 9.525 0 26 23.0 4500 9.5148 120 32 25.9 4500 9.525 0 32 22.9 4500 9.5164.5 135 32 27.8 4500 9.5164.5 135 26 28.0 4500 9.52222222DiscPosition(see pg. 25)21112210 (4) 3RecommendedValve (2)Approx.Wt. (lbs)TR574-26E 129TR500129TR574-26E 129TR574-26E 126TR574-26E 132TR500132TR574-26E 132TR501 (5) 135MaximumLoad & Infl.(lbs) – (psi)10000 – 105 (6)10500 – 120 (6)10000 – 105 (6)10000 – 105 (6)10000 – 10510000 – 10510500 – 12010250 – 110LIGHT TRUCKWHEELSBOLT-TOGETHERSPECIALTYWHEELSGENERALINFORMATIONItem1516Wheel Size22.5 x 13.0022.5 x 13.00WHEELSPartHandNumber Inset (3) Outset (8) Holes28465 6.12"28572 (9) 6.12"Heavy Duty (HD) Stud-Piloted Mounting (7)Heavy Duty Outer Cap Nut10-Hole, 13 3 /16" Heavy Duty Bolt Circle, 10.69" Bore, .625" Disc(1) These wheels use standard cap nuts with 7/8" (.875") spherical radius.(2) The valve shown is for the inset position.(3) Inset is defined as the lateral distance from the rim centerline to the mountingsurface of the disc. Inset places the rim centerline inboard of the mounting surface;outset places the rim centerline outboard of the hub surface.(4) Wheel disc has small valve access hole.(5) Wheel has two valve holes. Plug unused valve hole with Dill VS#902 orSchrader#345 plug.(6) Wheel may be used at 9370 Ibs -120 psi with 385/65R 22.5 LR J tires.------0024DiscPosition(see pg. 25)33RecommendedValve (2)Approx.Wt. (lbs)TR570 (10)TR570 (10) 133154MaximumLoad & Infl.(lbs) – (psi)10210 – 11012500 – 125(7)These wheels require Heavy Duty (HD) outer cap nuts with a 13/16" spherical radius. Standard cap nuts have a 7/8" (.875")spherical radius.(8)The wheel must only be installed in the inset position becausebolt chamfers are only on one side of the disc.(9)Rim flanges are reinforced.(10) The valve may require some bending (approx. 26°) to clear thedisc and allow the valve to seal properly.(11)TK - Product has liquid topcoat over epoxy black e-coat.