Sommerfeld's Tools For Wood Catalog - Digital Marketing Services

More documents

Recommendations

Info

SOMMERFELD’S TOOLSFor WoodTMOrder Line: 1-888-228-92683-Pc Tongue & Groove Cabinetmaking SetBuild stronger, better-fitting cabinets with less work, using MarcSommerfeld’s fail-safe Cabinetmaking System and these bitsThis special matched set of bits is the very foundation of Marc’swork-saving, common sense approach to cabinetmaking. Theway you build cabinets is about to change!HALF-PRICEOur woodworking, cabinetmaking, andfurniture-making tools in this countrywere all derived from Europe. The jointsthat were mainly used are mortise and tenon,tongue and groove, and stile and rail – all strongjoints that take time to construct. The buildingof cabinets in the United States has evolvedinto the use of simple butt joints done by facenailing or pocket screwing. These joints mayappear to be faster and easier to construct, butare most certainly not as accurate, nor as strong,and they are much more unsightly than the oldtraditional ones.With the Sommerfeld’s Tongue & GrooveCabinetmaking Set, we came up with a systemthat combines the best of that Old worldjoinery with our New World tooling. The resultsof this new method now make your cabinetsnot only stronger, but much more accurate,plus assuring you of that all-important hiddeninterlocking joint, along with surprising easeand quickness. Here’s a quick overview of howit works:Grooves are routed in the backs of all faceframe pieces before they are assembled.Tongues are routed on the fronts of the sidepanels, floors, and partitions.s s sGrooves are also cut in the backs and tops ofthe side panels for placement of corner blocks,and nail rails that have been previously cut withtongues.The Tongue & Groove joint is used in virtuallyevery step of Marc’s new cabinetmaking system,which you can master yourself by viewing hisDVD Cabinetmaking Made Easy.The big key to this whole system is thatsboth the Tongue & Groove bits are a perfectlymatchedpair in height. This allows repeatedchanging out of bits if necessary without adjusting the router.Note: use SOMMERFELD’S rubber grommet in doing this. See DVDCabinetmaking Made Easy.Every Tongue & Groove joint, no matter where it is used in theconstruction process, will automatically line up, fitting flush.All of our bit sets are packaged in a beautiful, custom-designedhardwood case to keep your bits safe, clean and easy to find formany years of service.Machines materials from ¾” to 1-1/8” thicks ssFlush TrimGrooveCutterTongueCutterHOW-TO DVDWith Bit Set PurchaseA $9.90 VALUEYours for only $4.90DVD: DVDS4Box has flushmountedmagnetic catch.Minimum Stock Thickness - 3/4” • Maximum Stock Thickness - 1-1/8”TOTAL VALUE: $126.80YOU SAVE: $16.90YOUR COST: $109.90Bit height set-up is a breezewith our Easy Set JigSEE PAGE 53ITEM Description ShankDia.Bearing02003 1/2” Shank Tongue & Groove Cutters 1/2” HC318DZZ & 698ZZ $99.9001019 1/2” Shank Flush Trim Cutter 1/2” R3ZZ $16.9003004 3-Pc Tongue & Groove Cabinetmaking Set 1/2” - $109.90Sale16Order online: www.sommerfeldtools.com
SOMMERFELD’S TOOLSFor WoodTMOrder Line: 1-888-228-92684-Pc Tongue & GrooveCabinetmaking PRO SetAdds a special 4” tall Mitered Molding Bit to our Tongue & Groove SetHALF-PRICEMolding bit produces decorative 3” wide stile & rail stock for mitered cabinet doors…then switch to the tongue & groove bits to create spline-like corner reinforcementsThis new set combines our Tongue &Groove Cabinetmaking set on theprevious page with our popular miteredmolding bit. The set includes the threebits needed for all your tongue & groovecabinetmaking needs, plus adds the miteredmolding bit which machines the surfacemolding for your mitered raised panel doors.The tongue & groove cutters are also usedto cut the tongues and grooves on the fourcorners of your door.The mitered molding bit machines theprofile on the top surface on 3” wide stiles andrails. The bit measures (4“) in length.s ss sThe set comes with two different-sizedbearings. The large bearing cuts ¼” deeptongue & grooves for cabinetmakingconstruction. The smaller bearing cuts ½”deep tongue & grooves for your mitered raisedpanel door.The groove cutter cuts a l/2” deep groove(when the small bearing is installed) in theright side of all miters. Also, it cuts the grooveon all inside edges of rails and stiles for raisedpanel insertion.The tongue cutter cuts a ½” deep tongue(when small bearing is installed) in the left sideof all miters.The flush trim bit trims off the end of the tongue so the tongue fitsinto stopped groove cut. This gives a mortise and tenon look to theoutside edge of the mitered raised panel door.s sAll of our bit sets are packaged in a beautiful, custom-designedhardwood case to keep your bits safe, clean and easy to find for manyyears of service.sMachines materials from ¾” to 1-1/8” thickHOW-TO DVDWith Bit Set PurchaseA $9.90 VALUEYours for only $4.90DVD: DVDS7Box has flush-mountedmagnetic catch.Bit height set-up is a breezewith our Easy Set JigSEE PAGE 53TOTAL VALUE: $216.70YOU SAVE: $36.80YOUR COST: $179.90Flush TrimGrooveCutterTongueCutterMiteredMolding BitMaking mitered raisedpanels is a snap as seen inMarc’s new DVDMitered Raised PanelsMade EasyItem DVDS7See Page 1117ITEM Description Shank Dia. Bearing Sale02003 1/2” Shank Tongue & Groove Cutters 1/2” HC318DZZ & 698ZZ $99.9001019 1/2” Shank Flush Trim Cutter 1/2” R3ZZ $16.9001010 1/2” Shank Mitered Molding Bit 1/2” R3ZZ $89.9004001 4-Pc Tongue & Groove Cabinetmaking PRO Set 1/2” - $179.90Order online: www.sommerfeldtools.com
Page 3 and 4: SOMMERFELD’S TOOLSFor WoodTMOrder
Page 8: SOMMERFELD’S TOOLSFor WoodTMOrder
Page 21 and 22: SOMMERFELD’S TOOLSFor WoodTM3-Pc
Page 27 and 28: SOMMERFELD’S TOOLSFor WoodTM6-Pc
Page 39 and 40: SOMMERFELD’S TOOLSFor WoodTMDovet
Page 41 and 42: SOMMERFELD’S Solid carbide flush
Page 43 and 44: SOMMERFELD’S TOOLSoove bitCore Bo
Page 45 and 46: l trimSOMMERFELD’S TOOLSFor WoodT
Page 47 and 48: 3/8SOMMERFELD’S TOOLSFor WoodTMPa
Page 51 and 52: SOMMERFELD’S TOOLSRail Rail & Sti
Page 55 and 56: ut ogeebitvel trimBBeadingll NoseBS
Page 59 and 60: SOMMERFELD’S TOOLSFor WoodTM86xxx
Page 61 and 62: BeadingieshamferSOMMERFELD’S TOOL
Page 63: 122901xxCSOMMERFELD’S TOOLSFor Wo
Page 66 and 67:
Slot cutter SOMMERFELD’S Face Fra
Page 68 and 69:
SOMMERFELD’S TOOLSFor WoodTMLong-
Page 70 and 71:
SOMMERFELD’S TOOLSFor WoodTMOrder
Page 72 and 73:
Page 74 and 75:
SOMMERFELD’S TOOLSFor WoodTMTrito
Page 76 and 77:
Page 78 and 79:
Page 80:
Sommerfeld’s Tools For Wood1408 C
show all

Sommerfeld's Tools For Wood Catalog - Digital Marketing Services

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?