Function Fittings - Chester Paul Company

More documents

Recommendations

Info

T65 Series 1/8" and 1/4"NPT and ISO G Shuttle Valves1 112Allows two independent signalsources to be connected to acommon pilot lineCan be used to perform an ‘OR’logic functionSelects the highest of twoapplied pressuresCan be combined to operate fromthree or more sourcesValves can be ganged togetherTechnical dataFluid:Compressed air,filtered, lubricated andnon-lubricated, inertgasesOperation:Shuttle valveMounting:Through holes in valve bodyPort Size:Female ThreadNPT1⁄8 NPT T65A18001⁄4 NPT T65A2800ISO GG1⁄8 T65C1800G1⁄4 T65C2800Operating Pressure:10 to 145 psi (0.7 - 10 bar)OperatingTemperature:0° to 175°F (-20°* to +80°C)*Consult our Technical Service for usebelow 35°F (2˚C)MaterialsBody: ZincBall: NitrileSeat: BrassI H BØFProduct Number Port Flow Factor WeightNPT ISO G Size Cv oz. (kg)T65A1800 T65C1800 1/8 0.42 1.9 (.055)T65A2800 T65C2800 1/4 0.64 4.6 (.130)NPT according to ANSI B1.20.1ADKGECJModel A B C D E F G H I J KT65A 1800 1/8 NPT 0.30 0.59 0.79 0.3 0.21 0.39 0.24 0.39 1.00 1.42T65C 1800 G1/8 0.30 0.59 0.79 0.3 0.21 0.39 0.24 0.39 1.00 1.42T65A 2800 NPT1/4 0.39 0.79 0.98 0.49 0.21 0.49 0.31 0.47 1.18 2.00T65C 2800 G1/4 0.39 0.79 0.98 0.49 0.21 0.49 0.31 0.47 1.18 2.00NPT according to ANSI B1.20.1G according to BS 2779/ISO 228/1FIT-65
<strong>Fittings</strong>T70, and C/511 SeriesQuick exhaust valves1/8" to 3/4"132Enables air to be exhaustedquickly from air reservoirs andcylinders.Allows higher cylinder speeds tobe achieved.Simple, compact design andconstruction.Very reliable in operation.Technical dataMedium:Compressed air, filtered, lubricatedand non-lubricatedOperating pressure:7 to 145 psi (0.5 to 10 bar) (T70)10 to 145 psi (0.7 to 10 bar) (S/511)10 to 100 psg (0.7 to 7 bar) (S/513,S/514)Operating temperature:-4°F to 176°F (-20°C to +80°C).Consult our Technical Service foruse below 35°F (+2°C).MaterialsBody & cover: zinc alloy (T70*1800& T70*2800, S/513),aluminum alloy (T70*3800 &T70*4800, S/511, S/514)Seals: nitrile (T70), polyurethane(S/51*)O-ring: nitrileElement: porous plastic (S/513,S/514)Model Inlet port Outlet port Exhaust port Cv Flow Factor Cv Flow Factor Weight Repair kitNPT ISO G Direction 1 - 2* Direction 2 - 3 oz (seals only)T70A 1800 T70C 1800 1⁄8 1⁄8 1⁄8 0.9 1.8 5.3 T70C1800K0T70A 2800 T70C 2800 1⁄4 1⁄4 1⁄4 1.9 2.5 4.6 T70C2800K0T70A 3800 T70C 3800 3⁄8 3⁄8 3⁄8 3.8 5.5 7.4 T70C3800K0T70A 4800 T70C 4800 1⁄2 1⁄2 1⁄2 5.3 5.9 6.7 T70C4800K0C/511 S/511 1/2 3/4 3/4 1.9/5.1** 10.8 11.0 QS/511/00* Flow factor measured at 87 psi (6 bar) (inlet) guideline direction** Alternative Cv shown for 14.5 psi (1 bar). For T70 Series, Cv approximately the same as at 6 bar.NPT threads per ANSI B1.20.1Model T70A1800 T70C1800 T70A2800 T70C2800 T70A3800 T70C3800 T70A4800 T70C4800 C/511*A 1⁄8 NPT G1/8 1⁄4 NPT G1/4 3⁄8 NPT G3/8 1⁄2 NPT G1/2 1/20 - 3/4ØB 0.75 0.75 0.75 0.75 1.18 1.18 1.18 1.18 –C A/F 0.75 0.75 0.75 0.75 1.18 1.18 1.18 1.18 –D 1.10 1.10 1.10 1.10 1.57 1.57 1.57 1.57 2.0E A/F 1.18 1.18 1.18 1.18 1.81 1.81 1.81 1.81 1.87F 0.60 0.60 0.60 0.60 0.61 0.61 0.61 0.61 –G 0.14 0.14 0.14 0.14 0.16 0.16 0.16 0.16 –H 2.09 2.09 2.09 2.09 2.89 2.89 2.89 2.89 3.38ØJ 1.14 1.14 1.14 1.14 1.81 1.81 1.81 1.81 –K 1.40 1.40 1.40 1.40 1.89 1.89 1.89 1.89 2.72* Note the shape of the C/511 is different. Consult our technical department for the exact specifications.HA GPort 2FDAPort 3KE A/FØBC A/FTypical Fill and Exhaust Times(seconds)Model Port Volume Fill Exhaustsize time timeT70A1800 1/8'' NPT 150 cc 0.036 0.021T70A2800 1/4'' NPT 150 cc 0.023 0.017T70A3800 3/8'' NPT 1500 cc 0.110 0.080T70A4800 1/2'' NPT 15,000 cc 0.460 0.480C/511 3/4'' NPT 15,000 cc 0.480 0.250Note: Fill time is 0 to 80 psig (0 to 5.5 bar), and exhaust time is 101 to20 psig (7.0 to 1.4 bar)AC A/FØJPort 1FIT-66www.norgren.com/usa
Page 7 and 8: FittingsPneufit C In-line Flow Cont
Page 9 and 10: FittingsM/800, C/800 SeriesHeavy du
Page 16: T15 SeriesPush-in flow controlsIn-l

Function Fittings - Chester Paul Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?