SDS - SeaForce 60 - Marine_Protective - English (us) - Jotun

More documents

Recommendations

Info

SeaForce 60 Page: 4/108 .Exposure controls/personal protectionTWA: 10 mg/m³ 8 hour(s). Form: Total dustACGIH TLV (United States, 1/2007).STEL: 10 mg/m³ 15 minute(s).TWA: 2 mg/m³ 8 hour(s).colophonyNIOSH REL (United States, 12/2001). Notes: Note: Carcinogenic inthe presence of formaldehyde, acetaldehyde, or malonaldehyde.See Appendix C (Aldehydes) See Appendix A - NIOSH PotentialOccupational CarcinogenTWA: 0,1 mg/m³ 10 hour(s). Form: All formsOSHA PEL 1989 (United States, 3/1989).TWA: 0,1 mg/m³ 8 hour(s). Form: All formsiron(iii)oxide OSHA PEL 1989 (United States, 3/1989).TWA: 5 mg/m³ 8 hour(s). Form: Respirable fractionTWA: 10 mg/m³ 8 hour(s). Form: Total dustACGIH TLV (United States, 1/2007).TWA: 5 mg/m³ 8 hour(s). Form: Respirable fractionOSHA PEL (United States, 11/2006).TWA: 10 mg/m³ 8 hour(s).OSHA PEL 1989 (United States, 3/1989). Notes: as FeSTEL: 10 ppm, (as Fe) 15 minute(s). Form: Total particulatesNIOSH REL (United States, 12/2001). Notes: as FeTWA: 5 mg/m³, (as Fe) 10 hour(s). Form: Dust and fumesSolvent naphtha (petroleum), light aromatic NIOSH REL (United States, 6/2001).TWA: 125 mg/m³ 10 hour(s). Form: All formsTWA: 25 ppm 10 hour(s). Form: All formsACGIH TLV (United States, 1/2005).TWA: 123 mg/m³ 8 hour(s). Form: All formsTWA: 25 ppm 8 hour(s). Form: All formsOSHA PEL 1989 (United States, 3/1989).TWA: 125 mg/m³ 8 hour(s). Form: All formsTWA: 25 ppm 8 hour(s). Form: All formsethylbenzeneACGIH TLV (United States, 1/2005). Notes: 2002 Adoption.Substances for which there is a Biological Exposure Index orIndicesSTEL: 125 ppm 15 minute(s). Form: All formsTWA: 100 ppm 8 hour(s). Form: All formsNIOSH REL (United States, 12/2001).STEL: 545 mg/m³ 15 minute(s). Form: All formsSTEL: 125 ppm 15 minute(s). Form: All formsTWA: 435 mg/m³ 10 hour(s). Form: All formsTWA: 100 ppm 10 hour(s). Form: All formsOSHA PEL (United States, 8/1997).TWA: 435 mg/m³ 8 hour(s). Form: All formsTWA: 100 ppm 8 hour(s). Form: All formsOSHA PEL 1989 (United States, 3/1989).STEL: 545 mg/m³ 15 minute(s). Form: All formsSTEL: 125 ppm 15 minute(s). Form: All formsTWA: 435 mg/m³ 8 hour(s). Form: All formsTWA: 100 ppm 8 hour(s). Form: All forms1-methoxy-2-propanol ACGIH TLV (United States, 1/2008).STEL: 553 mg/m³ 15 minute(s).STEL: 150 ppm 15 minute(s).TWA: 369 mg/m³ 8 hour(s).TWA: 100 ppm 8 hour(s).NIOSH REL (United States, 6/2008).STEL: 540 mg/m³ 15 minute(s).STEL: 150 ppm 15 minute(s).TWA: 360 mg/m³ 10 hour(s).TWA: 100 ppm 10 hour(s).OSHA PEL 1989 (United States, 3/1989).STEL: 540 mg/m³ 15 minute(s).STEL: 150 ppm 15 minute(s).Continued on next page
SeaForce 60 Page: 5/108 .Exposure controls/personal protectionTWA: 360 mg/m³ 8 hour(s).TWA: 100 ppm 8 hour(s).Engineering measuresEyesSkinRespiratoryHands :Hygiene measures: Use only with adequate ventilation. Use process enclosures, local exhaust ventilation orother engineering controls to keep worker exposure to airborne contaminants below anyrecommended or statutory limits. The engineering controls also need to keep gas, vaporor dust concentrations below any lower explosive limits. Use explosion-proof ventilationequipment.:::Safety eyewear complying with an approved standard should be used when a riskassessment indicates this is necessary to avoid exposure to liquid splashes, mists ordusts.Personal protective equipment for the body should be selected based on the task beingperformed and the risks involved and should be approved by a specialist before handlingthis product.Use a properly fitted, air-purifying or air-fed respirator complying with an approvedstandard if a risk assessment indicates this is necessary. Respirator selection must bebased on known or anticipated exposure levels, the hazards of the product and the safeworking limits of the selected respirator.Chemical-resistant, impervious gloves complying with an approved standard should beworn at all times when handling chemical products if a risk assessment indicates this isnecessary.: Wash hands, forearms and face thoroughly after handling chemical products, beforeeating, smoking and using the lavatory and at the end of the working period. Appropriatetechniques should be used to remove potentially contaminated clothing. Washcontaminated clothing before reusing. Ensure that eyewash stations and safety showersare close to the workstation location.9 .Physical and chemical propertiesPhysical stateFlash pointColorOdorRelative densityVOC: Liquid.: Closed cup: 28°C (82,4°F): Various colors.: Characteristic.: 1.7 g/cm 3: 3.5 pounds/gallon (US)14.19 pounds/gallon420 (g/l).Solubility:Insoluble in the following materials: cold water and hot water.Section 10. Stability and reactivityStability and reactivityHazardous decompositionproductsHazardous polymerization:::The product is stable.Under normal conditions of storage and use, hazardous decomposition productsshould not be produced.Under normal conditions of storage and use, hazardous polymerization will notoccur.Continued on next page
Page 1 and 2: SeaForce 601 .Trade nameCodeMateria
Page 3: SeaForce 60 Page: 3/10Section 6. Ac
Page 7 and 8: SeaForce 60 Page: 7/1013 .Disposal
Page 10: SeaForce 60 Page: 10/1016 .Other in

SDS - SeaForce 60 - Marine_Protective - English (us) - Jotun

Create successful ePaper yourself

Delete template?

Save as template?