systems

More documents

Recommendations

Info

uni Belt Material Selection PA6 - Polyamide Polyamide PA6 is a thermoplastic material. The combination of mechanical properties and chemical resistance makes this material suitable for many situations. Polyamide has a high resistance to wear and dynamic loads. This material is primarily used for sprockets. Color options: B D K N T W PA6-GF - Polyamide Glass Reinforced This Polyamide is reinforced with glass fiber. PA6-GF will be the right solution where higher stiffness and higher strength is required, compared to standard Polyamide. The combination of mechanical properties and chemical resistance makes this material suitable for many situations. Polyamide has a high resistance to wear and dynamic loads. Polyamide has also a lager working temperature range. Color options: B K PA6.6 - Polyamide Polyamide PA6.6 is a thermoplastic material with many fine properties. The material has a high resistance to wear, high strength and great stiffness. Furthermore, polyamide has a large temperature range. Color options: B D N W PA6.6-H PA6.6-H is a polyamid which contains the same fine properties as PA6.6. The PA6.6-H improves upon PA6.6 in applications where higher temperature resistance is needed e.g. shrink tunnels. Note: PA materials will absorb water in wet environments which will cause expansion of the dimension with approx. 1-2 %, depending on the temperature level and the humidity of the air. Color options: B D N W UV - Ultraviolet stabilizer The UV stabilizer is an additive recommended for plastic materials used for outdoor applications. The UV stabilizer is able to protect materials against direct sunlight to avoid destruction thereof. The UV stabilizer is FDA approved and will increase the lifetime of plastic materials. The UV stabilizer is available for the most common materials such as POM, PP and PE. uni Pin Material Selection SS304 Austenitic Stainless Steel Austenitic quality containing 18% chrome and 8% nickel. Werkstoff no. 1.4301 AISI 304 18/ 8 CrNi steel is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. However, in connection with evaporation of chloride-containing fluids, the 18/ 8 CrNi steel is not recommended, as stress corrosion can occur over time. 10
uni Pin Material Selection SS316 Austenitic Stainless Steel Austenitic quality containing 18% chrome, 10% nickel and 3% molybdenum Werkstoff no. 1.4404 AISI 316 18/ 10 CrNi steel with molybdenum is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. Molybdenum has been added to increase corrosion resistance particulary in chloride containing environments. PP - Polypropylene Polypropylene is a thermoplastic material with very good chemical resistance properties. PP is an economical material for applications with high temperatures. PE - Polyethylene PE is used in low temperature applications and where high impact resistance is required. PA6.6 - Polyamide Polyamide PA6.6 is a thermoplastic material with many fine properties. The material has a high resistance to wear, high strength and great stiffness. Furthermore, polyamide has a large temperature range. GR - Glass Reinforced Polyester Glass reinforced polyester is a material with an extremely high resistance to wear and heat. uni Reinforcement Material Selection SS316 Austenitic Stainless Steel Austenitic quality containing 18% chrome, 10% nickel and 3% molybdenum Werkstoff no. 1.4404 AISI 316 18/ 10 CrNi steel with molybdenum is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. Molybdenum has been added to increase corrosion resistance particulary in chloride containing environments. uni Rubber Material Selection Rubber code 01 N 03 N 03 K 05 I Rubber color Natural Black Ivory Hardness (shore A) 60 60 85 -40 to +80°C -40 to +80°C -40 to +80°C Temperature range °C °F -40 to +176°F -40 to +176°F -40 to +176°F FDA approved ✔ - ✔ Attachment to base link Natural 64 -40 to +125°C -40 to +257°F ✔ Mechanical Co-moulding Co-moulding Mechanical 11
Page 1 and 2: uni-chains BELT CATALOG belt system
Page 3 and 4: uni-chains ® Belt Catalog Innovati
Page 5 and 6: uni SNB M2 56 uni OPB 82 Pitch = 25
Page 7 and 8: uni Belt Material Selection Load Te
Page 9: uni Belt Material Selection Metal d
Page 13 and 14: Standard Modular Belt Range STANDAR
Page 15 and 16: uni M-PNB M1 Standard Selection uni
Page 17 and 18: uni M-PNB M1 Standard Sprockets No.
Page 19 and 20: uni M-QNB Standard Selection Patent
Page 21 and 22: uni M-QNB Standard Sprockets No. of
Page 23 and 24: uni M-SNB M3 Standard Selection uni
Page 25 and 26: uni M-SNB M3 Standard Sprockets No.
Page 27 and 28: uni Light Standard Selection Patent
Page 29 and 30: uni Light Standard Sprockets No. of
Page 31 and 32: uni Light Standard Selection Access
Page 33 and 34: uni S-MPB Standard Selection Patent
Page 35 and 36: uni S-MPB Standard Bi-directional S
Page 37 and 38: uni QNB Standard Selection Patent S
Page 39 and 40: uni QNB Standard Sprockets No. of t
Page 41 and 42: uni CNB Pitch 25.4 mm (1.00 in.) ST
Page 43 and 44: uni CNB uni CNB Single Link ® uni
Page 45 and 46: uni CNB Standard Selection Accessor
Page 47 and 48: uni Flex SNB Pitch 25.4 mm (1.00 in
Page 49 and 50: uni Flex SNB Standard Materials and
Page 51 and 52: uni Flex SNB uni Flex SNB Program B
Page 53 and 54: uni Flex SNB Belt Weights for uni F
Page 55 and 56: uni Flex SNB • • Product Suppor
Page 57 and 58: uni SNB M2 Standard Selection Paten
Page 59 and 60: uni SNB M2 Permissible Tensile Stre
Page 61 and 62:
uni SNB M2 Standard Sprockets No. o
Page 63 and 64:
uni Flex ONE STANDARD 63
Page 65 and 66:
uni Flex ONE uni Flex ONE Single Li
Page 67 and 68:
uni Flex ONE Standard Sprockets No.
Page 69 and 70:
uni SSB Pitch 38.1 mm (1.50 in.) US
Page 71 and 72:
uni SSB uni SSB Single Link ® uni
Page 73 and 74:
uni Light EP Pitch 38.1 mm (1.50 in
Page 75 and 76:
uni Light EP uni Light EP Single Li
Page 77 and 78:
uni L-SNB Pitch 50.0 mm (1.97 in.)
Page 79 and 80:
uni L-SNB uni L-SNB Single Link ®
Page 81 and 82:
uni L-SNB Standard Selection Access
Page 83 and 84:
uni OPB Standard Selection Patent M
Page 85 and 86:
uni OPB Standard Sprockets No. of t
Page 87 and 88:
uni OPB Standard Selection Accessor
Page 89 and 90:
uni CPB Standard Selection uni CPB
Page 91 and 92:
uni CPB Standard Sprockets No. of t
Page 93 and 94:
uni MPB Pitch 50.8 mm (2.00 in.) ST
Page 95 and 96:
uni MPB Standard Materials and Colo
Page 97 and 98:
uni MPB Belt Weights Belt material
Page 99 and 100:
uni MPB Standard Bi-directional Spr
Page 101 and 102:
uni MPB Standard Selection Accessor
Page 103 and 104:
uni X-MPB Standard Selection Patent
Page 105 and 106:
uni X-MPB Standard Bi-directional S
Page 107 and 108:
uni XLB Standard Selection Patent S
Page 109 and 110:
uni XLB Standard Bi-directional Spr
Page 111 and 112:
uni M-SNB M2 Made-To-Order Selectio
Page 113 and 114:
uni Light Made-To-Order Bricklayed
Page 115 and 116:
uni Flex SNB Made-To-Order Selectio
Page 117 and 118:
uni Light EP Made-To-Order Selectio
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
uni OPB Made-To-Order Selection uni
Page 125 and 126:
uni OPB Permissible Tensile Strengt
Page 127 and 128:
uni OPB Made-To-Order Selection Acc
Page 129 and 130:
uni Retainer Rings Standard Selecti
Page 131 and 132:
Technical Data Sheet for Belt/Chain
Page 133 and 134:
Technical Data Sheet for Belt/Chain
Page 135 and 136:
Warnings Fire uni-chains ® plastic
Page 137:
Get more information about your loc
show all

systems

Create successful ePaper yourself

Delete template?

Save as template?