product

More documents

Recommendations

Info

3.5. Wiring layout RTFS/RTN models only, equipped with NTC probe external cylinder and temperature adjustment on boiler RTFS/RTN models only, equipped with bulb probe external cylinder and temperature adjustment on cylinder (optional) F1 BIT F2 PIA F3 RIS F4 BOL F5 MIC F6 MAC Bi-thermal heat exchanger boiler Mono-thermal heat exchanger boiler and AQUA PREMIUM boiler CH only boiler System boiler Micro-reservoir boiler “AQUA PREMIUM “ boiler (encased models only) M3: Power supply connector M8: External probe M9: TA (room thermostat) M16: Tele-metering connector M2-M15: Boiler component connectors E.RIV: Detection electrode E.ACC: Ignition electrode TL: P : Water pump PV: V: Fan (model TFS only) TF: MVD: Three-way valve motor DK: Low water pressure switch SR: CH probe (10 Ohm B = 3435) SE: External temperature probe (10 Ohm B = 3977 - Optional) SS: DHW probe (10 Ohm B = 3435 max. length TIMER: three metres) TA: Room thermostat (Optional) CM1-CM2: Boiler type selection jumpers FL: Flow sensor VG: Gas valve Limit thermostat Fan pressure switch (model TFS only) Flue gas leak detection thermostat (model TN only) B: Probe-equipped external cylinder (remove R1) B1: Bulb probe-equipped external water cylinder (remove P1) DHW programmer (remove P1 when timer is installed) P1: Timer priority jumper R1: 10k Ohm resistance S: Bulb probe TR.ACC: Ignition transformer pic. 29 - Electric layout T (°C) 0 2 4 6 8 0 27203 24979 22959 21122 19451 10 17928 16539 15271 14113 13054 20 12084 11196 10382 9634 8948 30 8317 7736 7202 6709 6254 40 5835 5448 5090 4758 4452 50 4168 3904 3660 3433 3222 60 3026 2844 2674 2516 2369 70 2232 2104 1984 1872 1767 80 1670 1578 1492 1412 1336 90 1266 1199 1137 1079 1023 No. 10 table - Relation between temperature (°C) and nominal resistance (Ohm) of CH probe SR and DHW probe SS 34
3.6. Adaptation for use with other gases and burner adjustment These boilers are manufactured for the type of gas specified on the order, which is shown on the packaging label and the boiler rating plate. Adaptations after delivery must only be made by a qualified service engineer, using manufacturer-supplied accessories and implementing the modifications and adjustments for the necessary boiler set-up. Switching the boiler from natural gas to LPG • Remove the main burner. • Remove the main burner nozzles from the main burner and replace with suitable new gas nozzles of the correct diameter. WARNING! Always install copper gaskets. • Re-install the main burner. • On the electronic board, switch the MET- LPG jumper to the LPG position (pic. 30) • See subsections A, B and C. Switching the boiler from LPG to natural gas • Remove the main burner. • Remove the main burner nozzles from the main burner and replace with suitable new gas nozzles of the correct diameter. WARNING! Always install copper gaskets. • Re-install the main burner. • On the electronic board, switch the MET- LPG jumper to the MET position (pic. 30) • See subsections A, B and C. pic. 30 - Gas selection jumper C M Jumper position for natural gas Jumper position for LPG V A) Max power adjustment • Check the gas supply pressure (refer to tables 3, 4 and 5) • Remove the plastic cap (С, pic. 31), which is positioned on top on the modulating coil and protects the gas valve pressure adjusting nut and screw. • Connect a manometer to V test point in pic. 32. • Adjust the screw (maxR, pic. 33) to MAX by rotating fully clockwise. • Select WINTER boiler operation on switch 9 (pic. 1). • Start the boiler in “chimney sweep” mode (subsection 3.2.8.1). • Turn (external) nut К clockwise to increase nozzle pressure or vice versa (pic. 34). • In LPG-fuelled boilers, turn the brass nut К fully clockwise. pic. 31 - Gas valve modulation coil C) Final settings • Turn the Pacc screw (pic. 33) to the middle set point, exit “chimney sweep” mode (subsection 3.2.8.1.) and make sure the burner works correctly and silently. If necessary, increase or decrease ignition power via the Pacc adjuster (clockwise to increase, counter-clockwise to decrease). • Re-check the min and max gas valve pressure values. • Adjust as necessary. • Fit on plastic protective cap C. • Close gas pressure check valves. • Check for gas leaks. pic. 32 - Pressure test point Pacc maxR pic. 33 - Control panel setting W B) Min power adjustment • Disconnect the electrical wiring from the modulation coil (М, pic. 32). • Turn the burner on and check MIN pressure according to tables 3, 4 and 5. • To adjust the pressure, hold nut К still using a 100 mm tool, and turn screw W clockwise to increase or counter-clockwise to decrease the gas pressure (pic. 34). • Re-connect the electrical wiring to the modulation coil. pic. 34 - Gas valve adjustment K 35
Page 1 and 2: TAHITI DUAL IST 03 C 262 - 03 GB Hi
Page 3 and 4: General information for fitters, ma
Page 5 and 6: CONTENTS Warning page 2 General inf
Page 7 and 8: 1. INSTRUCTIONS FOR THE USER 1.1. C
Page 9 and 10: 1.2.2. Operation CENTRAL HEATING Us
Page 11 and 12: 1.3. Boiler shut-down If a malfunct
Page 13 and 14: User interface - Reset, stand-by, s
Page 15 and 16: CTFS and RTFS models 750 325 450 16
Page 17 and 18: RTN 24 8 6 11 10 3 12 2 7 4 1 5 13
Page 19 and 20: 2.5. General characteristics CTN 24
Page 21 and 22: BOILER WALL-HANGING TEMPLATE 1 2 C
Page 23 and 24: 750 2 Ø min. 2 Ø min. 1,5 m min.
Page 25 and 26: 3.2.7.2. 100/60 mm diameter coaxial
Page 27 and 28: WARNING The boiler may not work pro
Page 29 and 30: Turn knob 9 (pic. 1) to WINTER and
Page 31 and 32: 3.2.13. Room thermostat connection
Page 33: WARNING As regards treating water i
Page 37 and 38: and the following cleaning operatio
Page 39 and 40: BOILER STATUS MALFUNCTION PROBABLE

product

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?