V25.1 Software Guide Pulpmatic Ultima Eco Uno Incomatic V1.6

More documents

Recommendations

Info

1. Table of contents 1. Table of contents ................................................................................................. 2 2. Copyright and disclaimer ..................................................................................... 3 2.1 Copyright notice: ......................................................................................................... 3 2.2 Copyright Warning: ..................................................................................................... 3 2.3 Disclaimer: .................................................................................................................. 3 3. Cautionary notes .................................................................................................. 4 4. Release notes ...................................................................................................... 5 5. Parameter guide for software version 11 ............................................................. 7 6. Parameter guide for software version 15 ............................................................. 8 7. Parameter guide for software version 15.2 (Eco Only!) ....................................... 9 8. Parameter guide for software version V17 - V25.2 ............................................ 10 9. Guide to parameter settings ............................................................................... 12 10. Amending the parameter settings ...................................................................... 20 10.1 PCB Type C .............................................................................................................. 20 10.2 PCB Type A & B ....................................................................................................... 21 11. How to check current software version .............................................................. 22 12. Review machine performance ........................................................................... 24 13. How to upload a new software version .............................................................. 28 14. How to put the machine into exhibition mode .................................................... 31 15. How to put machine into workshop test mode ................................................... 36 16. Resistor values & colours .................................................................................. 39 17. How to programme the optional speaker system ............................................... 40 17.1 Programming the speaker ......................................................................................... 42 17.2 Adjusting speaker volume ......................................................................................... 42 18. Contact details ................................................................................................... 43 Copyright © 2017 DDC Dolphin Ltd. Page 2 of 43 March 17 SGPv25.1 –V1.6
2. Copyright and disclaimer 2.1 Copyright notice: Copyright © DDC Dolphin Limited (company number 02643023) (“Owner”), 2017. 2.2 Copyright Warning: The reproduction or transmission of all or part of this document, including all its content, schedules and appendices, whether by photocopying or storing in any medium by electronic means or otherwise, without the prior written consent of the Owner, is prohibited. The commission of any unauthorised act in relation to this technical guide may result in civil or criminal actions. The Owner asserts its moral rights under the Copyright, Designs and Patents Act 1988 to be identified as the author of this technical guide. 2.3 Disclaimer: The content of this document, including all its content, schedules and appendices is provided for general information and illustrative purposes only. It is not intended to amount to advice on which you should rely. While this technical guide has been prepared in good faith, the Owner makes no representations, warranties or guarantees (whether express or implied) that the content of this document, including all its content, schedules and appendices is accurate, complete or up-to-date and no responsibility or liability is or will be accepted by the Owner or by any of its officers, employees or agents in relation to the adequacy, accuracy, completeness or reasonableness of this document, including all its content, schedules and appendices. All and any such responsibility and liability is expressly disclaimed. No information set out, or referred to, in this document, including all its content, schedules and appendices shall form the basis of any contract. The Owner reserves the right to amend this document, including all its content, schedules and appendices at any time and gives no undertaking to provide the recipient with access to any additional information or to update this technical guide, or to correct any inaccuracies in it which may become apparent. Copyright © 2017 DDC Dolphin Ltd. Page 3 of 43 March 17 SGPv25.1 –V1.6
Page 1: Software Guide V25.1 Pulpmatic® Ul
Page 5 and 6: 4. Release notes Revision Notes Sui
Page 7 and 8: 5. Parameter guide for software ver
Page 9 and 10: 7. Parameter guide for software ver
Page 11 and 12: A2 - Machine start options for V17
Page 13 and 14: Machine start options V17 to curren
Page 15 and 16: Value 0 1 3 5 7 9 11 13 15 17 19 21
Page 17 and 18: Blocked drain alert delay Within th
Page 19 and 20: Mid-cycle dosing duration - seconds
Page 21 and 22: 10.2 PCB Type A & B SW2 SW1 SW4 SW3
Page 23 and 24: Step 3: Turn the power back on to t
Page 25 and 26: The “Input” menu shows the sens
Page 27 and 28: The “Other Analog” menu shows p
Page 29 and 30: Step 8: Double click on the .HEX Fi
Page 31 and 32: 14. How to put the machine into exh
Page 33 and 34: • Turn the machine OFF at the iso
Page 35 and 36: • Refit the PCB housing lid • R
Page 37 and 38: • Turn the machine OFF at the iso
Page 39 and 40: 16. Resistor values & colours Liste
Page 41 and 42: 5. Name the text document MODE-A00
Page 43: 18. Contact details Company Name: D

V25.1 Software Guide Pulpmatic Ultima Eco Uno Incomatic V1.6

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?