BM_2018_KATALOG_EN_WEB

More documents

Recommendations

Info

PUR IN 24 Polyurethane Based, Two Component, Injection System Description PUR IN 24 is a polyurethane based, two component injection system which reacts with water quickly and increases system’s volume 10-15 times. Fields of Application • To stop water leakage from cavities and cracks of concrete walls and floors of tunnels, bridges, sheet piles and similar constructions. • To insulation of cold joints, • On water tanks and swimming pools, • To insulation of interior basements. Features and Benefits • Stops water leakage on applied surface, provides water isolation. • Fills the holes of system without lose volume. • Safely used in moist concrete. • Blocks negative water flow. Application Procedure Preparation of Substrate Prior to the injection, the cracks to be worked on are sealed using EPOX repairing mortars. Along the course of the cracks, holes are drilled at a distance of 10 to 15 cm to each other on alternating sides of the crack. Packers are inserted into the injection holes and (if possible) injected proceeding from the bottom to the top. The diameter of the holes depends on the packers used. Application Method Component A and B are stirred separately under low speed mixer. Then Component B is added slowly into the Component A under low speed mixer and mixed together approximately 3-4 minutes till a homogenous mixture is obtained. PUR IN 24 is injected using a mechanical pump under low pressure. When low viscosity liquid mixture is applied, it expands rapidly and it becomes a solid foam within approximately 45 seconds. Consumption Consumption depends on usage area. Package A component: 20 kg + B component: 2 kg = 22 kg set 116 Ürün teknik föylerini web sitemizden indirebilirsiniz.
WALL CL 100 Mold (Fungus) Preventive Impregnation Primer Description WALL CL 100 is ready to use water based solution used on painted or unpainted surfaces for microbiological cleaning and protection purposes. Fields of Application Used on interior and exterior mineral surfaces. Features and Benefits • Protects the wall against mold forming microorganisms. • Prepare the surface before paint application Application Procedure Preparation of Substrate Clean the surface with a wet clean bristle brush and wipe it with a dry cloth. Application Method WALL CL 100 is ready to use, do not need dilution. Applied with a soft pile brush. Do not apply it with spray gun. Top coat paint and primer application can be done after completely dry. Consumption According to surface type and absorbency 5-10 m 2 area can be cleaned with 1 kg product. Package 1 kg and 5 kg packages Ürün teknik föylerini web sitemizden indirebilirsiniz. 117
Page 3 and 4:
ABOUT US Our company, which has bee
Page 5:
Floor Systems EPOX PR 100 EPOX PR 2
Page 8 and 9:
B PR 100 Bituminous Membrane Primer
Page 10 and 11:
B PR 102 Bitumen Solution Descripti
Page 12 and 13:
SCHOUBIT 1K Bitumen-Rubber Modified
Page 14 and 15:
SCHOUBIT PLAST 1K Bitumen-Rubber Ba
Page 16 and 17:
BROOT 120 Bitumen-Rubber Based, Ant
Page 19 and 20:
Cement Based Waterproofing Products
Page 21 and 22:
CHIMEX 127 Cement-Acrylic Based, Tw
Page 23 and 24:
CHIMEX 235 Cement-Acrylic Based, Tw
Page 25 and 26:
CRYSTAL 25 Cement Based, Crystalize
Page 27:
TURBOPLUG Cement Based, Set in 3-4
Page 30 and 31:
WHITECOAT Elastomeric Acrylic Resin
Page 32 and 33:
SOLARCOAT UV Resistant, Acrylic-Bas
Page 34 and 35:
PUR 625 Polyurethane Based, UV Resi
Page 36 and 37:
PUR 425 Standard Pure Polyurea Desc
Page 38 and 39:
PUR 410 Hybrid Polyurea Description
Page 40 and 41:
POLIXA 2 Polyurethane Based, Waterp
Page 42 and 43:
PU-B 1K Polyurethane Based, Bitumen
Page 44 and 45:
HYBRID 120 Hybrid-Polymer Based, On
Page 46 and 47:
SILOX Invisible Water Repellent and
Page 49 and 50:
Admixtures
Page 51 and 52:
LATEX Waterproofing and Adherence I
Page 53 and 54:
CRYSTAL PW 25 Crystalline Waterproo
Page 55:
PROGEL -10 Concrete Antifreeze Admi
Page 58 and 59:
PUMAST 600 Polyurethane Based, One
Page 60 and 61:
PS PRIMER Primer for Polysulphide B
Page 62 and 63:
JOINTPAST PS-H Polysulphide Based,
Page 64 and 65:
PUB 401 Polyurethane-Bitumen Based,
Page 66 and 67:
SWELLBAND Bentonite Based, Swelling
Page 68 and 69: FLEXBIT Bituminous, Elastic Waterst
Page 70 and 71: EPOX 220 Epoxy Based, Two Component
Page 72 and 73: BMAST 100 Bitumen-Rubber Based, Hot
Page 74 and 75: BMAST WF 310 Bituminous Waterproofi
Page 77 and 78: Floor Systems
Page 79 and 80: EPOX PR 200 Epoxy Based, Two Compon
Page 81 and 82: EPOX FL 500 Epoxy Based, Two Compon
Page 83 and 84: EPOX FL 700 Epoxy Based, Two Compon
Page 85 and 86: PURSELF 201 Polyurethane Based, Two
Page 87 and 88: FH KORUND Corundum Aggregate, Concr
Page 89 and 90: FH RELEASE AGENT Release Agent for
Page 91 and 92: LH 130 Surface Hardener and Shiner
Page 93 and 94: LH 415 Dusting Preventive and Surfa
Page 95 and 96: CURE P Paraffin Wax Emulsion Based,
Page 97 and 98: BRUT PR Bonding Agent for Plaster o
Page 99 and 100: SELFING 600 Cement Based, Self-Leve
Page 101 and 102: EPOCOL 220 Epoxy-Coal Tar Based, So
Page 103: MD 200 Steel Mold Release Agent Des
Page 106 and 107: REPAMERK 1 Cement Based, Repair Mor
Page 108 and 109: REPAMERK 301 Cement Based, Structur
Page 110 and 111: GRT 20 Cement Based Grouting Mortar
Page 112 and 113: EPOX 310 Epoxy Based, 3 Component,
Page 114 and 115: EPOX 305 Epoxy Based, Two Component
Page 116 and 117: POLY 308 Polyester Based Chemical A
Page 121 and 122: Complementary Products
Page 123 and 124: DRAIN-B HDPE Based, Protective Drai
Page 125 and 126: PROFILE AL Aluminum Based, Isolatio
Page 127 and 128: B-SELF TAPE AL Bitumen Based, Self
Page 129 and 130: PH 127 Waterproofing Tape with Fabr
Page 131 and 132: LDPE MEMBRANE Root Inhibitive Foil
Page 134 and 135: NOTES
show all

BM_2018_KATALOG_EN_WEB

Create successful ePaper yourself

Delete template?

Save as template?