Norbar Catalogue 2019

More documents

Recommendations

Info

SCREWDRIVERS AND TORQUE WRENCHES UKAS ACCREDITED CALIBRATION CERTIFICATION Accredited Calibration Laboratory No. 0256 The hallmark of Norbar’s high standard of workmanship is clearly seen in the fact that we were the first torque equipment manufacturer to have an in-house UKAS accredited calibration laboratory. We have no intention of resting on our laurels and take pride that we still provide the most comprehensive service available, ensuring we evolve to continue to meet your needs. Norbar’s laboratory has approval for torques between 0.005 and 108,500 N·m and operates to BS EN ISO/IEC 17025:2005, which sets standards for the technical competence of the laboratory. This should not be confused with laboratories claiming ISO 9001 which relates only to a laboratory's quality management systems. The part numbers shown below are for a comprehensive calibration, for all new torque screwdrivers and torque wrenches, including NorTronic®, up to the maximum capacity shown. Please see page 123 for Norbar's After Sale Service. 12 ONE DIRECTION TWCC4.CW Up to 400 Nm / 300 lbfft TWCC5.CW Up to 1,000 Nm / 750 lbfft TWCC6.CW Up to 3,000 Nm / 2,200 lbfft 12 TWO DIRECTIONS TWCC4.CW+CCW Up to 400 Nm / 300 lbfft TWCC5.CW+CCW Up to 1,000 Nm / 750 lbfft TWCC6.CW+CCW Up to 3,000 Nm / 2,200 lbfft 39 enquiry@norbar.com | www.norbar.com
HANDTORQUE® MULTIPLIERS HANDTORQUE® TORQUE MULTIPLIERS Torque wrench design offers just two solutions to the challenge of applying higher torques: either the load at the handle must be higher or the lever length must be greater. Clearly there are practical and safety limits to both of these solutions. For example, a Norbar model 1000 (1,000 N·m) torque wrench is 1.7 m long with the extension handle fitted. As this is already quite long, how would one apply 2,000 or 3,000 N·m? Often there will not be the space to operate a torque wrench of sufficient length to comfortably apply such high torques and the chance that the wrench might slip off the nut increases as length increases. Norbar’s solution is to use a compact, epicyclic gearbox called a HandTorque® multiplier to accurately multiply the input torque provided by a torque wrench by a fixed ratio. This fixed ratio might be in the order of 5:1, 25:1 or even up to 125:1 for very high torque application. This means that a much smaller torque wrench can be used for a given torque application and the combined weight of the torque multiplier and torque wrench will often be lower than for a single large torque wrench. For example, one could apply 1,000 N·m using a Norbar Model 1000 torque wrench weighing 5.8 kg or an HT- 52/22.2 combined with a NorTorque® 60 with a total weight of just under 2 kg and a lever length of just 310 mm. The Norbar HandTorque® multiplier range is the most comprehensive available. Standard products are available up to 47,500 Nm (35,000 lbf·ft) and ‘specials’ to 300,000 Nm (220,000 lbf·ft). A range of ‘nose extensions’ for reaching difficult to access bolts and a full range of torque transducers for highly accurate torque monitoring are available. Torque Reaction 41 HandTorque Torque Multipliers 43 Anti Wind-Up Ratchets 45 HandTorque® HT3-1000 46 HandTorque® HT3 Series 46 HandTorque® HT4 Series 47 HandTorque® Compact Series 48 HandTorque® Compact Series Kits 49 HandTorque® Standard Series 49 HandTorque® Small Diameter Series 51 enquiry@norbar.com | www.norbar.com 40
Page 1 and 2: CATALOGUE 2019
Page 3 and 4: INTRODUCTION ABOUT NORBAR UNITED KI
Page 5 and 6: t l bf.ft lbf.ft lbf.f 60 50 0 4 N.
Page 7 and 8: INTRODUCTION INTRODUCTION TO TORQUE
Page 9 and 10: SCREWDRIVERS AND TORQUE WRENCHES TO
Page 11 and 12: SCREWDRIVERS AND TORQUE WRENCHES IS
Page 13 and 14: SCREWDRIVERS AND TORQUE WRENCHES NO
Page 17 and 18: SCREWDRIVERS AND TORQUE WRENCHES SL
Page 19 and 20: SCREWDRIVERS AND TORQUE WRENCHES PR
Page 27 and 28: SCREWDRIVERS AND TORQUE WRENCHES IN
Page 33 and 34: SCREWDRIVERS AND TORQUE WRENCHES CL
Page 37 and 38: SCREWDRIVERS AND TORQUE WRENCHES SP
Page 39: SCREWDRIVERS AND TORQUE WRENCHES LA
Page 43 and 44: HANDTORQUE® MULTIPLIERS TORQUE REA
Page 45 and 46: HANDTORQUE® MULTIPLIERS HANDTORQUE
Page 53 and 54: POWERED TORQUE TOOLS POWERED TORQUE
Page 55 and 56: POWERED TORQUE TOOLS EVOTORQUE®2 E
Page 57 and 58: POWERED TORQUE TOOLS EVOTORQUE®2 M
Page 59 and 60: POWERED TORQUE TOOLS EVOTORQUE® BA
Page 61 and 62: POWERED TORQUE TOOLS PNEUMATIC TORQ
Page 63 and 64: POWERED TORQUE TOOLS PNEUTORQUE® P
Page 69 and 70: POWERED TORQUE TOOLS ET, ET2, EBT,
Page 71 and 72: POWERED TORQUE TOOLS OPTIONAL REACT
Page 73 and 74: POWERED TORQUE TOOLS RIGHT ANGLE GE
Page 75 and 76: POWERED TORQUE TOOLS RIGHT ANGLE GE
Page 77 and 78: POWERED TORQUE TOOLS PNEUTORQUE® S
Page 79 and 80: POWERED TORQUE TOOLS PNEUTORQUE® S
Page 81 and 82: TORQUE MEASUREMENT TORQUE MEASUREME
Page 83 and 84: TORQUE MEASUREMENT TRUCHECK 0.1 - 2
Page 85 and 86: TORQUE MEASUREMENT PROFESSIONAL TOR
Page 87 and 88: TORQUE MEASUREMENT TORQUE TOOL TEST
Page 89 and 90: TORQUE MEASUREMENT SPARES FOR INSTR
Page 91 and 92:
TORQUE MEASUREMENT STATIC TRANSDUCE
Page 93 and 94:
TORQUE MEASUREMENT FLANGE MOUNTED T
Page 95 and 96:
TORQUE MEASUREMENT ANNULAR TRANSDUC
Page 97 and 98:
TORQUE MEASUREMENT ANNULAR TRANSDUC
Page 99 and 100:
TORQUE MEASUREMENT TRANSDUCER LEADS
Page 101 and 102:
TORQUE MEASUREMENT TORQUE WRENCH CA
Page 103 and 104:
TORQUE MEASUREMENT TORQUE WRENCH CA
Page 105 and 106:
TORQUE MEASUREMENT TEST FIXTURES 4
Page 107 and 108:
HYDRAULIC TOOL CALIBRATION FIXTURES
Page 109 and 110:
HYDRAULIC TOOL CALIBRATION FIXTURES
Page 111 and 112:
HARSH ENVIRONMENT INSTRUMENTS HARSH
Page 113 and 114:
HARSH ENVIRONMENT INSTRUMENTS HARSH
Page 115 and 116:
HARSH ENVIRONMENT INSTRUMENTS INTER
Page 117 and 118:
ULTRASONIC MEASUREMENT ULTRASONIC M
Page 119 and 120:
CALIBRATION BEAMS & WEIGHTS CALIBRA
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
SPARES KITS SPARES KITS 8 TORQUE SC
Page 127 and 128:
SPARES KITS SPARES KITS 8 NORTORQUE
Page 129 and 130:
CALIBRATION SERVICES DECLARATION OF
Page 131 and 132:
CALIBRATION SERVICES UKAS ACCREDITE
Page 133 and 134:
CALIBRATION SERVICES OTHER CERTIFIC
Page 135 and 136:
TERMS & CONDITIONS of delivery (or
show all

Norbar Catalogue 2019

Create successful ePaper yourself

Delete template?

Save as template?