You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
MOUNTING INSTRUCTIONS<br />
There are a few things that you should do before you begin to install your new<br />
Pro-Trac 2. Read these instructions entirely before beginning installation.<br />
The following tools are required for installation: Philips head screwdriver or electric<br />
drill, Pliers and Adjustable Wrench.<br />
Components: One CSA/UL approved Pro-Trac 2, One Accessory Kit and<br />
Instructions.<br />
IMPORTANT WARNING<br />
Do NOT operate your Pro-Trac with the carriage<br />
and motor facing upwards (when you take it out<br />
of the box). The track must face down or the<br />
chain will bind.<br />
Fig. 1A - STANDARD MOUNTING<br />
Fig. 1B - HEAVY MULTI-LAMP MOUNTING<br />
Fig. 1C - GREENHOUSE MOUNTING<br />
Carriage<br />
Fixture Hook<br />
Drill and counter sink hole, screw<br />
head must be flush<br />
Front View<br />
Your Pro-Trac 2 is shipped fully assembled.<br />
All you have to do is mount it. If you have any<br />
questions or service concerns, or should your Pro<br />
Trac stop functioning properly please do NOT<br />
start to fix it.<br />
Call our toll free service number<br />
1-800-265-4769<br />
FRONT<br />
OIL HERE<br />
Fig. 2 Fig. 3 - BACK<br />
<strong>Rambridge</strong> <strong>Wholesale</strong> <strong>Supply</strong> warrants to the original purchaser that this product will be free from defects in material<br />
and workmanship for a period of two years from date of purchase. The Company’s obligation under this warranty shall<br />
be strictly and exclusively limited to the repairing or replacing, and any such equipment and parts there of which the<br />
Company finds to be defective in material or workmanship under normal use and service within such a period of two<br />
years. The Company reserves the right to satisfy such obligation in full by refunding the full purchase price for any<br />
defective equipment. In order to obtain warranty service, contact your retailer. Proof of purchase must be supplied for<br />
warranty returns. Shipping must be prepaid.<br />
This warranty shall not apply to this product or any part thereof which has been taken apart, damaged by accident,<br />
abused, misused, modified, neglected, altered or misapplied and is expressly in lieu of all warranties expressed or<br />
implied and of all other obligations or liabilities on part of the seller.<br />
1. To mount your Pro-Trac on the<br />
ceiling, use screws provided and be<br />
certain the screws penetrate into the<br />
wood and not just drywall (Fig 1A). Do<br />
not risk having your lighting system fall.<br />
2. In applications where a heavy load<br />
is being tracked (multiple lamps or a<br />
ballast lamp) we recommend using a<br />
mounting screw in every mounting hole<br />
(Fig 1B). If you cannot have each screw<br />
bite securely into wood (1 inch minimum)<br />
refer to mounting instruction #3.<br />
3. For two point greenhouse mounting,<br />
use strong cable and attach each end of<br />
the Pro-Trac to the greenhouse purlins.<br />
To increase stability and prevent side-toside<br />
motion, attach 2 cables at the centre<br />
of the Pro-Trac 2 forming a “V” (Fig 1C).<br />
It is easy to rig a pulley system which can<br />
raise and lower your entire system.<br />
4. Hang vertical reflector lamp from<br />
the centre hole in the carriage or from<br />
the two outside holes (Fig 2). Targus<br />
horizontal shades have been designed to<br />
bolt directly onto the Pro-Trac carriage.<br />
Make sure you leave enough cord<br />
between the ballast and the lamp so<br />
the Pro-Trac can move easily from end<br />
to end without excessive side pull.<br />
HELPFUL INFORMATION<br />
The carriage travels from one end to<br />
the other in approximately 8 minutes,<br />
pausing at each end for approximately 1<br />
minute for a uniform garden profile.<br />
Lubricate the motor once a year by<br />
removing the cover plate and putting a<br />
few drops of oil (10W-30) onto the felt<br />
pad at the front of the motor (Fig 3). If<br />
the track stops running or gets slow, this<br />
bearing usually is in need of a cleaning<br />
with solvent and then re-oil.<br />
59<br />
Tehnical Information