OM, 2748 GLS, (CA), 96043005000, 2008-03, Ride ... - Husqvarna
OM, 2748 GLS, (CA), 96043005000, 2008-03, Ride ... - Husqvarna
OM, 2748 GLS, (CA), 96043005000, 2008-03, Ride ... - Husqvarna
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
TO MOVE FORWARD AND BACKWARD<br />
(See Fig. 7)<br />
The direction and speed of movement is controlled by the<br />
Motion Control Lever (J).<br />
J<br />
TO ADJUST MOWER CUT TING HEIGHT<br />
(See Fig. 8)<br />
The po si tion of the at tach ment lift le ver (A) de ter mines the<br />
cut ting height.<br />
A<br />
FIG. 7<br />
• Start tractor with motion control le ver in neutral (N)<br />
position.<br />
• Release parking brake.<br />
• Slowly move motion control lever to desired position.<br />
FIG. 8<br />
• Put attachment lift lever in desired cutting height slot.<br />
The cutting height range is ap prox i mate ly 1" to 4". The<br />
heights are measured from the ground to the blade tip with<br />
the engine not running. These heights are approximate<br />
and may vary depending upon soil conditions, height of<br />
grass and types of grass being mowed.<br />
• The average lawn should be cut to approximately 2-1/2<br />
inches during the cool season and to over 3 inches<br />
during hot months. For healthier and better looking<br />
lawns, mow often and after moderate growth.<br />
• For best cutting performance, grass over 6 inches<br />
in height should be mowed twice. Make the first cut<br />
relatively high; the second to de sired height.<br />
OPERATION<br />
10<br />
TO ADJUST GAUGE WHEELS (See Fig. 9)<br />
Gauge wheels are prop er ly ad just ed when they are slight ly<br />
off the ground when mower is at the desired cutting height<br />
in operating position. Gauge wheels then keep the deck<br />
in proper position to help prevent scalping in most terrain<br />
conditions.<br />
NOTE: Adjust gauge wheels with tractor on a flat level<br />
surface.<br />
• Adjust mower to desired cutting height (See “TO AD-<br />
JUST MOWER CUT TING HEIGHT” in this sec tion of<br />
manual).<br />
• With mower in desired height of cut po si tion, gauge<br />
wheels should be assembled so they are slightly off<br />
the ground. In stall gauge wheel in ap pro pri ate hole.<br />
Tighten se cure ly.<br />
• Repeat for all, installing gauge wheel in same adjustment<br />
hole.<br />
FIG.9<br />
TO OPERATE MOWER<br />
Your tractor is equipped with an operator presence sensing<br />
switch. Any attempt by the operator to leave the seat with<br />
the engine running and the attachment clutch engaged will<br />
shut off the engine. You must remain fully and centrally<br />
positioned in the seat to prevent the engine from hesitating<br />
or cutting off when operating your equipment on rough,<br />
rolling terrain or hills.<br />
• Select desired height of cut with attachment lift lever.<br />
• Start mower blades by engaging at tach ment clutch<br />
control.<br />
TO STOP MOWER BLADES -<br />
disengage at tach ment clutch con trol.<br />
<strong>CA</strong>UTION: Do not operate the mower<br />
without either the en tire grass catcher,<br />
on mowers so equipped, or the deflector<br />
shield (S) in place.<br />
FIG. 10<br />
S