305.4 Instalación de vapor5.4.1 Descripción de la instalación de vaporBasic ProFAN B15 FAN P15FAN B45 FAN P4541-...61-...81-...Pmax 1500 PaPmin -800 Pamin. 20 %–min. 5 %–max. 4 mDS60DS80Pmax 1500 PaPmin -800 Pa41-...61-...81-...KS10KS10Rmin. 300 mmØmin. 200 mmmax. 4 mRmin. 300 mmmin. 20 %+min. 5 % DS22–DS60DS80min. 300 mmmin. 20 %–Ømin. 200 mm
315.4.2 Emplazamiento y montaje de las lanzas de distribución de vaporEl lugar de montaje de las lanzas de distribución de vapor se determina en el momento del diseñodel sistema de aire acondicionado. Para garantizar una humidificación correcta del aire en el conductodeberá observar las siguientes indicaciones.Determinación de la distancia de humidificaciónEl vapor de agua que sale de la lanza de distribución de agua necesita una distancia determinadahasta que el flujo de aire haya asimilado el vapor de forma que ya no sea visible. Esta distancia sedenomina distancia de humidificación ”B N” y sirve de base para la determinación de las distanciasmínimas con respecto a los restantes componentes de la instalación.Distancia dehumidificación B NExpansión y zona de mezclaϕ1: Humedad del aire antes de la humidificaciónϕ2: Humedad del aire después de la humidificaciónLa determinación de la distancia de humidificación ”B N” depende de diferentes factores. Para facilitarla determinación de la distancia de humidificación ”B N” se puede utilizar la siguiente tabla. Losvalores orientativos detallados en esta tabla se refieren a una temperatura de aire de alimentaciónde 15 °C. Los valores en negrita sólo son válidos para las lanzas de distribución de vapor 41-...,61-... y 81-... y los valores entre paréntesis para el sistema de distribución de vapor OptiSorp.Humedad deentradaLongitud de la distancia de humidificación B Nen mHumedad de salida ϕ2 en %HRϕ1 en %HR 40 50 60 70 80 905 0,9 (0,22) 1,1 (0,28) 1,4 (0,36) 1,8 (0,48) 2,3 (0,66) 3,5 (1,08)10 0,8 (0,20) 1,0 (0,26) 1,3 (0,34) 1,7 (0,45) 2,2 (0,64) 3,4 (1,04)20 0,7 (0,16) 0,9 (0,22) 1,2 (0,30) 1,5 (0,41) 2,1 (0,58) 3,2 (0,96)30 0,5 (0,10) 0,8 (0,17) 1,0 (0,25) 1,4 (0,36) 1,9 (0,52) 2,9 (0,88)40 – 0,5 (0,11) 0,8 (0,20) 1,2 (0,30) 1,7 (0,45) 2,7 (0,79)50 – – 0,5 (0,13) 1,0 (0,24) 1,5 (0,38) 2,4 (0,69)60 – – – 0,7 (0,16) 1,2 (0,30) 2,1 (0,58)70 – – – – 0,8 (0,20) 1,7 (0,45)Para anchuras de conducto