LED Bar 648/5 RGB

More documents

Recommendations

Info

Group 1 – 48 channel occupancy. Each LED group is controlled individually. CH 43-48 CH 19-24 CH 37-42 CH 13-18 26/51 CH 31-36 CH 7-12 CH 25-30 Master/Slave Mode If 2 or more LED Bars 648/5 RGB are connected together, first disconnect them from the DMX signal. Set one or more devices on Sound Activation Mode (See No DMX Auto/Sound/Manual) and you are in Master/Slave Mode. CLEANING AND MAINTENANCE The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year. The following points have to be considered during the inspection: 1) All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded. 2) There must not be any deformations on housings, fixations and installation spots (ceiling, suspension, trussing). 3) The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. CH 1-6 DANGER TO LIFE! Disconnect from mains before starting maintenance operation! We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents! There are no serviceable parts inside the device except for the fuse. Maintenance and service operations are only to be carried out by authorized dealers. Replacing the fuse If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating. Before replacing the fuse, unplug mains lead. Procedure: Step 1: Open the fuseholder on the rear panel. Step 2: Remove the old fuse from the fuseholder. Step 3: Install the new fuse in the fuseholder. Step 4: Replace the fuseholder in the housing. Should you need any spare parts, please use genuine parts. If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer. 51913856_V_1_0.DOC
Should you have further questions, please contact your dealer. TECHNICAL SPECIFICATIONS Power supply: 230 V AC, 50 Hz ~ Power consumption: 50 W Sound-control: via built-in microphone Dimensions (LxWxH): 800 x 115 x 135 mm Weight: 5 kg Maximum ambient temperature T a : 45° C Maximum housing temperature T B (steady state): 60° C Fuse: F 2 A, 250 V Number of channels: 48 Number of LEDs: 648 Please note: Every information is subject to change without prior notice. 19.12.2006 © 27/51 51913856_V_1_0.DOC
Page 1 and 2: Für weiteren Gebrauch aufbewahren!
Page 3 and 4: INTRODUCTION ......................
Page 5 and 6: Bitte überprüfen Sie vor der erst
Page 7 and 8: Soll das Gerät transportiert werde
Page 9 and 10: Anschluss ans Netz Schließen Sie d
Page 11 and 12: Non-DMX Modi Drücken und drehen Si
Page 13 and 14: Kanal 6: Interne Programme Dezimal:
Page 15 and 16: abgestimmte Vorschriften werden vom
Page 17 and 18: Please make sure that there are no
Page 19 and 20: OVERVIEW (1) Attachment eyelet (2)
Page 21 and 22: The device must only be connected w
Page 23 and 24: DMX-Mode: Group The LEDs on the fro
Page 25: Group 4 - 6 channel occupancy; 2 se
Page 29 and 30: Avant tout, assurez-vous que l'appa
Page 31 and 32: Ne nettoyez pas l'appareil avec des
Page 33 and 34: Alimentation Branchez l’appareil
Page 35 and 36: Modes Non-DMX Pressez l’Encoder e
Page 37 and 38: 211 - 240 83 - 94% Programme intern
Page 39 and 40: L'intérieur de l'appareil ne conti
Page 41 and 42: Antes de la puesta en marcha inicia
Page 43 and 44: DESCRIPCIÓN DE LAS PARTES (1) Ojet
Page 45 and 46: Sólo conectar el aparato a una ins
Page 47 and 48: O: Cuando quiere ajustar el Step Ti
Page 49 and 50: Group 4 - Ocupación 6 canales; 2 s
Page 51: Cuando el cable de alimentación se

LED Bar 648/5 RGB

Create successful ePaper yourself

Delete template?

Save as template?