Manual en PDF - Kruger
Manual en PDF - Kruger
Manual en PDF - Kruger
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
USING THE MULTIREG ADJUSTABLE<br />
NOZZLE.(FIG. 14)<br />
Pressure must be selected with the gun<br />
switched off.<br />
Low pressure washing and deterg<strong>en</strong>t suction.<br />
Move the nozzle forward.<br />
Washing at high pressure with a conc<strong>en</strong>trated<br />
jet of water<br />
Turn the nozzle in an anti-clockwise direction.<br />
Washing at high pressure with a fan-shaped<br />
jet of water<br />
Turn the nozzle in a clockwise direction.<br />
USE OF THE DOUBLE LANCE (fig. 15).<br />
The double lance allows the operator to select a low<br />
or high pressure jet. The pressure is selected with the<br />
gun in pos. 1. High pressure: pos. 2. Low pressure<br />
and deterg<strong>en</strong>t intake: pos. 3.<br />
REGULATING PRESSURE.<br />
This chapter concerns only those models<br />
provided with the “pressure regulating”<br />
device. The pressure regulator, fig. 16, allows the<br />
operator to adjust the working pressure. Wh<strong>en</strong> knob<br />
C is turned in an anti-clockwise direction (B) (minimum),<br />
the working pressure is reduced.<br />
ADVICE ON USING DETERGENTS<br />
This cleaner has be<strong>en</strong> designed for use with the<br />
deterg<strong>en</strong>ts supplied or recomm<strong>en</strong>ded by the manufacturer.<br />
The use of other deterg<strong>en</strong>ts or chemicals may influ<strong>en</strong>ce<br />
the safety of the cleaner.<br />
1) For <strong>en</strong>vironm<strong>en</strong>tal compatibility, we recomm<strong>en</strong>d a<br />
reasonable use of deterg<strong>en</strong>ts, according to the instructions<br />
on the pack.<br />
2) From the range of recomm<strong>en</strong>ded products, choose<br />
the one most suited to the washing job to be done and<br />
dilute it with water according to the instructions on the<br />
pack or in the catalogue of the deterg<strong>en</strong>ts most suited<br />
for the type of hot or cold water cleaner.<br />
3) Ask your dealer for the deterg<strong>en</strong>ts catalogue.<br />
OPERATING PHASES FOR CORRECT CLEA-<br />
NING WITH DETERGENTS.<br />
1) Prepare the solution of deterg<strong>en</strong>t at the conc<strong>en</strong>tration<br />
most suitable for the type of dirt and the surface that<br />
is to be washed.<br />
16<br />
2) Start the cleaner, turn on the deterg<strong>en</strong>t tap (if<br />
pres<strong>en</strong>t), switch on the deterg<strong>en</strong>t suction control on<br />
the lance (fig. 14) and spray the dirty surface with the<br />
diluted product, working from bottom to top.<br />
Let it react for a few minutes.<br />
3) Rinse the whole surface well from top to bottom at<br />
high pressure.<br />
4) After using with deterg<strong>en</strong>t, flush out the intake circuit;<br />
place the deterg<strong>en</strong>t suction hose (fig. 12) in a tank of<br />
clean water and let the pump run for 1 minute with the<br />
dosing tap turned fully on and the lance in deterg<strong>en</strong>t<br />
delivery condition.<br />
ADDITION OF DETERGENT<br />
MAINTENANCE<br />
The deterg<strong>en</strong>ts must not be allowed<br />
to dry on the object to be<br />
cleaned.<br />
Thedeterg<strong>en</strong>t adjustm<strong>en</strong>t knob (Fig. 21) is used to<br />
increase/decrease deterg<strong>en</strong>t flow.<br />
Fill the deterg<strong>en</strong>t tank (Fig. 7) with deterg<strong>en</strong>t, di-lute<br />
as recomm<strong>en</strong>ded.<br />
Wh<strong>en</strong> high pressure is selected, the deterg<strong>en</strong>t<br />
CANNOT be delivered! (Fig. 22)<br />
ONLY THE OPERATIONS AUTHORIZED IN THIS<br />
INSTRUCTIONS MANUAL MAY BE CARRIED OUT<br />
BY THE USER.<br />
ALL OTHER OPERATIONS ARE FORBIDDEN.<br />
For maint<strong>en</strong>ance of the high pressure pump, the<br />
electrical parts and all parts with a safety function, you<br />
must apply to our technical service c<strong>en</strong>tre.<br />
Disconnect the machine from the power and water<br />
supply before carrying out any maint<strong>en</strong>ance jobs.<br />
Close the water supply tap (see chapters on connecting<br />
to the electricity and water mains). Once maint<strong>en</strong>ance<br />
has be<strong>en</strong> completed, <strong>en</strong>sure that the closing panels<br />
have be<strong>en</strong> correctly reassembled and anchored with<br />
the screws provided before reconnecting the cleaner<br />
to the mains.<br />
Failure to do so may cause a risk of<br />
electric shock.<br />
RECAUTIONS AGAINST FROST.<br />
The cleaner must not be exposed to frost.<br />
If the cleaner is left in premises where it is exposed to<br />
frost, wh<strong>en</strong> work is over or for storage, antifreeze must<br />
be used to prev<strong>en</strong>t serious damage to the hydraulic<br />
circuit.