600 Watt WIND TURBINE ÉOLIENNE 600 Watt TURBINA EÓLICA ...

More documents

Recommendations

Info

Multiple Function Charge Controller (Wind Power) Contrôleur de charge intelligent à conversion optimale d'énergie (MPPT) et à fonctions multiples pour maîtriser la puissance du vent Controlador de Carga Multifunción (Aerogeneración) User’s Manual Notice D’utilisation Manual del Usario 1
Thank You for purchasing the Sunforce MPPT (maximum power point tracking) charge controller. So as to gain the most beneficial, efficient operation, and long term use from your new MPPT charge Controller, please read carefully the information and explanation of features contained in this manual. You are also advised to keep this manual in a safe place for ready reference. Introduction: A MPPT, or maximum power point tracker is an electronic AC to DC converter that optimizes the match between the turbine and the battery bank, DC motor, or DC pump. (These are usually called power trackers or MPPT’s for short. The power output of a wind turbine varies almost directly with the amount wind - but the voltage and current do not. The current drops off much faster than the voltage. Under low wind conditions the panel or turbine may be putting out 16 volts, but the amperage will be lower than the units rating. What does a Maximum Power Point Tracker (MPPT) do 1. A MPPT controller looks at the output of your wind generator, and compares it against the battery voltage. It then uses an algorithm to calculate the absolute best power that the wind turbine can put out. The MPPT controller then converts its findings to the best possible voltage in order to allow for maximum AMPS running in to the battery bank. Most MPPT controllers are at 92-97% efficient however the Sunforce controller is 97-99% efficient in the conversion. Here is where the optimization or maximum power point tracking comes in. For example, A MPPT controller takes the 17 volts at 4.4 amps and converts it so that what it puts out to the battery is no longer 4.4 amps at 17 volts, rather 5.77 amps at 13 volts. This allows for your 75 <strong>Watt</strong>s of power to be used to its maximum ability. In an extreme case, for example having a fully discharged battery at 10.5 volts, you would get nearly 7 amps at 10.5 volts out of the MPPT in to the battery. A MPPT controller tracks the maximum power point, which will vary from the STC (Standard Test Conditions) rating under almost all situations. Under very cold conditions, a 75 watt panel is actually capable of putting out over 80 watts of power because output increases as temperature decreases. However, it is important to note that if you do not have a way of tracking that power point, you are going to lose power. On the other hand under very hot conditions, the power output rate drops and you lose power as the temperature rises. Overview: The Maximum Power Point Tracking (MPPT) charge controller enables the <strong>600</strong> watt wind turbine to achieve its highest possible performance by periodically tracking the Maximum Power Point of the turbine. The MPPT can be used with battery systems from 12v to 24v DC. The MPPT set points are fully adjustable to allow use with virtually any battery type, chemistry, and charging profile. This user guide will demonstrate the basic operation and troubleshooting of your MPPT charge controller. Features: Maximum Power Point Tracking technology, to increase the overall efficiency of your wind system. 12 / 24 Volt automatic detection system. Temperature-Compensated, Three-Stage I-U Curve Charge Regulation. 2
Page 1 and 2:
600 Watt WIND TURBINE ÉOLIENNE 600
Page 3 and 4:
Choosing your Sunforce 600 Watt Win
Page 5 and 6:
Battery Protection Voltage: Rated L
Page 7 and 8:
Multiple Turbine installation: 7
Page 9 and 10:
4. PACKAGE CONTENTS Check the parts
Page 11 and 12:
Step2: Take out the blades from box
Page 13 and 14:
Step 6: Install the hub on the wind
Page 15 and 16: 6. MAINTENANCE Your Sunforce Produc
Page 17 and 18: Possible Battery Configurations (su
Page 19 and 20: Sunforce Products 600 Watt Wind Tur
Page 21 and 22: Limitation of Liability UNDER NO CI
Page 23 and 24: câblage provenant des batteries, u
Page 25 and 26: Puissance de sortie nominale Plage
Page 27 and 28: Installation de plusieurs éolienne
Page 29 and 30: 4. CONTENU DE L'EMBALLAGE Comparez
Page 31 and 32: Figure 2 Étape 2 : Retirez les pal
Page 33 and 34: Figure 7 Étape 6 : Installez le mo
Page 35 and 36: Figure 13 Étape 9 : Schéma de l'a
Page 37 and 38: 5) Mon éolienne 600W de Sunforce P
Page 39 and 40: Veuillez prendre le temps de consul
Page 41 and 42: La validité de la garantie au clie
Page 43 and 44: 1. SEGURIDAD Su Turbina Eólica Sun
Page 45 and 46: 2. TABLA DE MODELOS Y ESPECIFICACIO
Page 47 and 48: Precaución: Por favor revise la si
Page 49 and 50: Instalación múltiple: 49
Page 51 and 52: 4. CONTENIDO DEL PAQUETE Revisar la
Page 53 and 54: Tornillo Hexagonal 4 (M5xL20) Arand
Page 55 and 56: Figura 6 Paso 5: Para instalar la t
Page 57 and 58: Figura 13 Paso 9: Diagrama del prod
Page 59 and 60: (4) ¿Se puede conectar la Turbina
Page 61 and 62: apropiada a tierra (ilustrada a con
Page 63 and 64: GARANTÍA Sunforce Products garanti
Page 65: For more information or technical s
Page 69 and 70: ON 30A 15A Chargeable Deep Cycle Ba
Page 71 and 72: Check Step: 1. In normal situations
Page 73 and 74: Sleeping happens when the wind turb
Page 75 and 76: ___________________________________
Page 77 and 78: Dimensions : 22,9 x 12,7 x 7,6 cm (
Page 79 and 80: Schéma de câblage 14
Page 81 and 82: instructions du menu qui suit. Assu
Page 83 and 84: Float (Charge d'entretien) - Le con
Page 85 and 86: ___________________________________
Page 87 and 88: negativo de la carga CC 12V (o inve
Page 89 and 90: Comprobación de Funcionamiento: 7.
Page 91 and 92: elegida. Sin embargo, siempre es me
Page 93: For more information or technical s
show all

600 Watt WIND TURBINE ÉOLIENNE 600 Watt TURBINA EÓLICA ...

Create successful ePaper yourself

Delete template?

Save as template?