M 132 - M 172 - BLUESHIELD

More documents

Recommendations

Info

3. INSTALLATION3.1 CONNECTING THE EQUIPMENT TOTHE MAIN SUPPLYThe equipment works within an input range of±10%.Check to ensure that the power outlet is equippedwith a fuse that is capable of carrying the ampsindicated on the data plate of this unit.3.2 SELECTING A LOCATIONSpecial installation may be requiredwhere gasoline or volatile liquids are present(See NEC Article 511 or CEC Section 20). Donot move or operate this equipment where itcould tip over. When selecting a location forthis equipment, ensure that the followingguidelines are followed:1. Use data plate to determine input powerrequirements.2. The operator must have unobstructed access toall controls and equipment connections.3. Do not position equipment in small, closedplaces. Ventilation of the power source isextremely important. Make sure that the louverson the side panels are not obstructed andthat there is no risk of obstruction during operation.4. Avoid areas where dust or other objects couldbe sucked into the system.5. Equipment must not obstruct corridors or workactivities of other personnel.6. Position the power source securely to avoidfalling or overturning.7. Understand the risk of falling equipment situatedin overhead positions.3.3 CHANGING POLARITYTURN OFF WELDER BEFORE MAKINGCONNECTIONS.(Consult wire data to verify polarity requirements.)DCEN (Straight Polarity)1. Connect the ground cable to the positive receptacleinside the unit.2. Connect the power cable to the negative receptacleinside the unit.DCEP (Reverse Polarity)1. Connect the ground cable to the negativereceptacle inside the unit.2. Connect the power cable to the positive receptacleinside the unit.INSTALLING GAS HOSE AND REGULATOR1. Install the gas hose on the inlet connectionlocated on the rear of the machine.2. Install the regulator on the cylinder outlet connectionlocated on the top of the compressedgas cylinder.3. Connect the male gas hose connection to thefemale regulator connection.3.4 INSTALLING WELDING GUNTURN OFF WELDER BEFORE MAKINGCONNECTIONS.Before connecting the torch, ensure that the driverolls, gun liner and contact tip match the diameterof the wire being used.When installing the welding gun, follow thesequence described below.8
INSTALLING WELDING GUNTURN OFF WELDER BEFORE MAKING CONNECTIONS.12349
Page 1 and 2: M 132 - M 172USER MANUALINSTRUCTION
Page 3 and 4: WARNINGRead and understand this ent
Page 5 and 6: performed by a qualified electricia
Page 7: 2.1 SPECIFICATIONS2. SPECIFICATIONS
Page 11 and 12: 3.7 INSTALLING SG 185 SPOOL GUN1. L
Page 13 and 14: 5.2 REPLACING THE GUN LINER1. Turn
Page 15 and 16: AVERTISSEMENT :Avant d'installer, d
Page 17 and 18: de soudage de plomb, béryllium, ca
Page 19 and 20: L'INSTALLATION ET L'ENTRETIEN DE L'
Page 21 and 22: 3. INSTALLATION3.1 RACCORDEMENT DU
Page 23 and 24: 3.5 INSTALLATION DE LA BOBINE DE FI
Page 25 and 26: 4. UTILISATION4.1 COMMANDES DU PANN
Page 27 and 28: ÍNDICE1 NORMAS DE SEGURIDAD-LEA AN
Page 29 and 30: un respirador con alimentador de ai
Page 31 and 32: LA INSTALACIÓN DEL EQUIPO Y EL MAN
Page 33 and 34: 3. INSTALACIÓN3.1 CONEXIÓN DEL EQ
Page 35 and 36: 3.5 INSTALACIÓN DE LA BOBINA Y LAR
Page 37 and 38: 4. FUNCIONAMIENTO4.1 MANDOS PANEL A
Page 39 and 40: ✍
Page 41 and 42: VOLT-AMPERES CURVES - COURBES VOLT-
Page 43 and 44: ELECTRICAL DIAGRAM - SCHÉMA ÉLECT
Page 45 and 46: M 132R. COD. DESCRIPTION DESCRIPTIO
Page 47 and 48: M 172R. COD. DESCRIPTION DESCRIPTIO
Page 50 and 51: CONDITIONS GÉNÉRALES DE GARANTIEE
Page 52: • SHOULD YOU WISH TO MAKE A COMPL

M 132 - M 172 - BLUESHIELD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?