Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Pullers<br />
Pullers<br />
Multipurpose Bearing/Puller Set<br />
Slide Hammer Puller Set<br />
P210<br />
Harmonic Balancer & Steering<br />
Wheel Puller Set<br />
Includes eight sets of side bolts:<br />
3 each: 3 ⁄8” - 16” x 4” 3 each: 3 ⁄8” - 24” x 2”<br />
3 each: 5 ⁄16” - 18” x 2” 3 each: M8 - 1.25” x 80mm<br />
3 each: M10 - 1.50” x 50mm 2 each: 1 ⁄4” - 28” x 3”<br />
2 each: 5 ⁄16” - 24” x 3 1 ⁄2” 3 each: 5 ⁄16” - 18” x 4 1 ⁄2”<br />
Weight: 4.0 lbs.<br />
P50109<br />
2 Pieces Bearing Separator Puller Set<br />
Part No.<br />
P501<br />
P309<br />
Weight: 3.0 lbs.<br />
Description<br />
0” - 2 1 ⁄4” capacity<br />
Timing gear puller<br />
Part No. Description Weight<br />
P300 Puller Bearing Separator Set 9.3 lb.<br />
Includes:<br />
One pressure screw 3 ⁄4” - 16 x 7 1 ⁄4” long<br />
One pressure screw 3 ⁄4” - 16 x 5 1 ⁄2” long<br />
One yoke bar - 3 pin hole, spread range 3 1 ⁄4” to 5 1 ⁄2”<br />
One yoke bar - 2 pin hole, spread range 2 3 ⁄8” to 3 3 ⁄8”<br />
Two adjustable clamp bolts<br />
Two jaw pins with spring ball<br />
Three pairs of puller jaws:1 3 ⁄8” max, 1 5 ⁄8” max, 1 3 ⁄4” max<br />
Three pairs of hex capped bolts<br />
Blow molded carrying case<br />
Use on Pitman arms, timing gear, bearing alternators,<br />
power steering, harmonic pulleys, and crankshaft pulleys.<br />
Part No. Description Weight<br />
P495 Slide Hammer Puller Set 18.5 lb.<br />
Includes:<br />
5 lb. slide hammer<br />
2-way block<br />
3-way block<br />
Cone block<br />
3 Internal/external jaw 6 1 ⁄2”<br />
3 Internal/external jaw 3 3 ⁄4”<br />
3 Pilot bearing jaws 2 3 ⁄8”<br />
Front hub puller<br />
Small yoke puller<br />
Center screw<br />
Dent puller attachment<br />
Grip wrench adapter with single lead<br />
Puller hook<br />
Blow molded carrying case<br />
PO10T<br />
3 Pieces Push Puller Set<br />
Part No.<br />
Description<br />
P309<br />
Timing Gear Puller<br />
Spread range 1 1 2” - 4 1 ⁄4”<br />
One center screw 5 ⁄8” - 18 x 5 1 ⁄2” long<br />
Two hex head cap screw ( 3 ⁄8” - 16 x 3”)<br />
One extra center screw 5 ⁄8” - 18 x 13” long<br />
(Ideal for use with P309)<br />
P5013A<br />
2 Pieces Bearing Separator Set<br />
Part No.<br />
P501<br />
P503<br />
Weight: 6.9 lbs.<br />
Description<br />
0” - 2 1 ⁄4” capacity<br />
0” - 4 1 ⁄4” capacity<br />
Puller Bearing Separator, 5 Ton Capacity<br />
Part No. Description Weight<br />
P293 Puller Bearing Separator Set 10 lb.<br />
Includes:<br />
Two bearing separators (2” & 3”)<br />
Four sets of extension shafts<br />
5” Cross slide puller with center screw ( 9 ⁄16”-10 x 7”)<br />
Blow molded carrying case<br />
P310<br />
P312<br />
Large Gear and Pulley Puller<br />
Spread range 2” to 7 3 ⁄4”<br />
One center screw 3 ⁄4” - 16 x 11 5 ⁄8” long<br />
Cap screws not included<br />
10 Ton Push Puller<br />
Reach Max: 8 1 ⁄4<br />
Spread range: 2 1 ⁄8” to 7 1 ⁄4”<br />
One 1 ⁄2” center screw 3 ⁄4” - 16 x 12” long, tip end<br />
threaded 5 ⁄8” - 18<br />
One center nut<br />
Two sliding plates with hex nut<br />
Two legs 6 3 ⁄4” long with tip end threaded 5 ⁄8”- 18<br />
Two end caps 1 1 ⁄2” long<br />
Can be used with P503 and P507<br />
Plastic spare parts container (empty)<br />
Blow molded carrying case<br />
296<br />
297