Notice d'utilisation - Atika
Notice d'utilisation - Atika
Notice d'utilisation - Atika
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Maintenance and Care<br />
Before each maintenance and cleaning work<br />
− Switch off device<br />
− Wait unitl the machine comes to a stop<br />
− Pull out power plug<br />
Maintenance and repair work other than those described in this<br />
chapter is only allowed to be carried out by service staff.<br />
For maintaining and cleaning, removed security devices must<br />
unconditionally be mounted properly and proved again.<br />
Use only original parts. Other parts can result in unexpected<br />
damages and injuries.<br />
Cleaning<br />
Observe the following to maintain the operability of the<br />
machine:<br />
• Do not wash down device with water.<br />
• Remove splints and dust only with a brush or vacuum<br />
cleaner.<br />
• Slightly spray maintenance spray or dry-film lubricant on the<br />
height adjustment device (5) of the thicknessing table.<br />
• Take care that the feed rollers remain free of rust and<br />
resin.<br />
• Remove resin residues from the table plate surfaces.<br />
Resin residues can be removed with a commercial<br />
maintenance and care spray.<br />
• Apply a thin film of sliding wax on the feed, delivery and<br />
thicknessing table plates.<br />
• Regularly remove resin from the blade shaft and from the<br />
parts attached to it. For this purpose put the clamping<br />
device, the blade holders and the blades into paraffin,<br />
gasoline or commercial resin remover for 24 hours.<br />
Maintenance<br />
The cutting blades are wearing parts and will become dull after<br />
longer or frequent use.<br />
If so, replace the cutting blades or have them sharpened.<br />
Regrinding of cutting blades is only allowed to a height of<br />
15 mm.<br />
Always use cutting blades which are approved for the machine<br />
(see “Technical data”).<br />
Replace or sharpen both cutting blades together.<br />
Before replacing or sharpening the cutting<br />
blades unplug the machine.<br />
Danger of cutting! Wear gloves when replacing the<br />
cutting blades.<br />
Replacing the cutting blades<br />
1. Remove the guide plate (1).<br />
2. Fully push off the blade shaft guard (12) from the table plate.<br />
3. Loosen the nuts of the clamping screws (A) using the<br />
supplied open-end spanner. T<br />
If the nuts are not visible, carefully turn the blade shaft (34)<br />
using a waste wood block.<br />
4. Remove the clamping device (36) and the blade (35). U<br />
5. Clean all parts including the blade slots in the blade shaft.<br />
6. Re-insert the clamping device with a new or sharpened<br />
blade.<br />
7. Align the blade:<br />
- Place the setting gauge (32) for the cutting blades onto<br />
the delivery table plate. V<br />
- Firmly press the gauge onto the delivery table plate while<br />
making sure that the edge of the setting gauge is flush<br />
with the edge of the delivery table plate.<br />
- Then, the curved surface of the setting gauge presses<br />
the blade in its correct position.<br />
- Retighten the clamping screws. W<br />
When doing so start in the centre and move outwards.<br />
8. Replace also the other blade of the blade shaft.<br />
9. Push the blade shaft guard over the blade shaft.<br />
Maintenance of the gearbox X<br />
1. Remove the cap nuts and the both recessed head screws<br />
from the gearbox cover.<br />
2. Remove the gearbox cover (10).<br />
3. Remove wood dust and shavings using the shavings<br />
extractor or a brush.<br />
4. Slightly spray maintenance spray on the roller chain (38)<br />
and on the bearings of the belt roller and pulley.<br />
Do not use grease.<br />
5. Re-mount the gearbox cover.<br />
Transport<br />
<br />
Remove mains plug before each transport.<br />
Before any transport make sure that the blade shaft guard<br />
fully covers the blade shaft.<br />
This will avoid injury by the blades.<br />
When handling do not take hold on the feed or delivery<br />
table. Take hold on the bottom of the machine.<br />
22