PerfectView CAM50 - Waeco

More documents

Recommendations

Info

_CAM50.book Seite 30 Montag, 7. Mai 2012 3:12 15 Mounting the camera PerfectView CAM50 8 Mounting the camera 8.1 Tools required For installation and assembly you will require the following tools: • Drill bit set (fig. 1 1, page 2) • Drill (fig. 1 2, page 2) • Screwdriver (fig. 1 3, page 2) • Set of ring or open-ended spanners (fig. 1 4, page 2) • Measuring ruler (fig. 1 5, page 2) • Hammer (fig. 1 6, page 2) • Centre punch (fig. 1 7, page 2) To make and test the electrical connection, the following tools are required: • Diode test lamp (fig. 1 8, page 2) or voltmeter (fig. 1 9, page 2) • Insulating tape (fig. 1 11, page 2) • Cable bushing sleeves, if necessary To fasten the cables you may require additional cable binders. 8.2 Mounting the camera ! CAUTION! I NOTE Select a location for the camera and attach it so securely that it cannot under any circumstances fall off and injure bystanders (e.g. by being knocked off by branches brushing over the roof of the vehicle). If installing the camera alters the vehicle height or length specified in the vehicle documents, your vehicle must be inspected by the appropriate authorities. Make sure that you are in possession of documents verifying that your vehicle has passed this inspection. 30 EN
_CAM50.book Seite 31 Montag, 7. Mai 2012 3:12 15 PerfectView CAM50 Mounting the camera Observe the following installation instructions: • To provide a suitable viewing angle, the camera must be attached at a height of at least 2 m. Ensure that you have a firm place from which to work when mounting the camera. • Ensure that the installation location of the camera is sufficiently firm (e.g. to prevent the camera from being knocked down by branches that may brush over the roof of the vehicle). • Mount the camera bracket horizontally and in the middle of the rear of the vehicle (fig. 0, page 5). • The most secure type of attachment is with screws fitted through the body. Please observe the following instructions: – There must be sufficient space for the mounting procedure behind the chosen installation location. – Suitable measures must be taken to prevent water penetrating through any holes made (e.g. by using screws and sealant and/or spraying the outer attachment parts with a sealant). – The location on the body where you wish to attach the camera must be rigid enough to allow the camera to be tightly fastened. • Check beforehand that there is sufficient room for the drill head to come out on the other side (fig. 2, page 3). • If you are not sure about the location you have chosen, consult the vehicle manufacturer or dealer. I NOTE We recommend greasing the threads of the bolts to prevent corrosion. When mounting the camera, proceed as follows: ➤ Hold the camera on the chosen location and mark at least two different points for the drill holes (fig. a, page 5). ➤ Using a hammer and centre punch, gently pre-punch the previously marked points to prevent the drill head from slipping off. EN 31
Page 1 and 2: _CAM50.book Seite 1 Montag, 7. Mai
Page 29: _CAM50.book Seite 29 Montag, 7. Mai
Page 81 and 82:
_CAM50.book Seite 81 Montag, 7. Mai
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
_CAM50.book Seite 101 Montag, 7. Ma
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
show all

PerfectView CAM50 - Waeco

Create successful ePaper yourself

Delete template?

Save as template?