Squelch für WTC
Squelch für WTC
Squelch für WTC
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
Applications Note<br />
Sensor Platine (rechts)<br />
(A) an einen der drei 100Ohm<br />
Widerstande anlöten.<br />
(B) an Pin 4 vom Modula6 Stecker<br />
anlöten.<br />
(C) an Masse anlöten.<br />
Auswerter Platine (links)<br />
9 und 10 Lautsprecher<br />
12 7Volt vom Funkgerät<br />
13 PTT Eingang<br />
14 Audio NF Ausgang<br />
15 Mic NF Eingang<br />
S <strong>Squelch</strong> Ausgang OK 100 mA<br />
Einbau:<br />
1. Die Sensorplatine (rechts) wird nachträglich in die Ladehalterung <strong>WTC</strong>601, <strong>WTC</strong>606, <strong>WTC</strong>631, <strong>WTC</strong>632, <strong>WTC</strong>641, <strong>WTC</strong>660 eingebaut.<br />
Siehe Abbildungen. Bei der <strong>WTC</strong>663, <strong>WTC</strong>668, <strong>WTC</strong>632B, <strong>WTC</strong>660E und <strong>WTC</strong>685 ist die Sensorschaltung bereits auf der Hauptplatine<br />
vorhanden.<br />
2. Die Auswerter Platine (links) wird auf den 15poligen Zubehöranschluss gesteckt.<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 1 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 2 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 3 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 4 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>601E, GPN6136E / <strong>WTC</strong>606E, GPN6141E-<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 5 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
Applications Note<br />
Bei <strong>WTC</strong>601C/D, GPN6136C/D / <strong>WTC</strong>606C/D, GPN6141C/D wird der Anschluss (A) von der Sensorplatine an den Federkontakt 6 von der<br />
Seitenanschlussplatine angelötet. Die Anschlüsse (B) und (C) von der Sensorplatine werden, wie bei <strong>WTC</strong>601E, GPN6136E / <strong>WTC</strong>606E,<br />
GPN6141E angeschlossen.<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 6 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>632 und <strong>WTC</strong>632A.<br />
Bei <strong>WTC</strong>632B ist die <strong>Squelch</strong> Sensor Elektronik serienmassig vorhanden und braucht nicht nachgerüstet werden.<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 7 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>631, <strong>WTC</strong>641<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 8 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>660b,<strong>WTC</strong>660c, <strong>WTC</strong>660d,<br />
Bei <strong>WTC</strong>660E ist die <strong>Squelch</strong> Sensor Elektronik serienmassig vorhanden und braucht nicht nachgerüstet werden.<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 9 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>685 Durch schließen der Lötbrücke werden alle Duplex Funktionen deaktiviert und der <strong>Squelch</strong> Sensor aktiviert.<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 10 06.06.2008
<strong>Squelch</strong> <strong>für</strong> <strong>WTC</strong><br />
<strong>WTC</strong>688 Durch schließen der Lötbrücke werden alle Duplex Funktionen deaktiviert und der <strong>Squelch</strong> Sensor aktiviert.<br />
Applications Note<br />
© WEMPE Elektronic GmbH, Leinenweberstr.6, D-36351 Bad Hersfeld Seite 11 06.06.2008