Crimpen ⢠Crimping - Timmer Tools & Technics
Crimpen ⢠Crimping - Timmer Tools & Technics
Crimpen ⢠Crimping - Timmer Tools & Technics
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Kabelschere D20 mit Doppelschneide, für Al+Cu Kabel<br />
Cable shears D20 with dual cutting edges, for Al+Cu cables<br />
• geringer Kraftaufwand durch<br />
günstige Übersetzungsverhältnisse<br />
und neuartiger Schneidengeometrie<br />
• kein Quetschen, keine Verformung<br />
• mit Vor- und Nachschnitt (1. und 2. Schneide)<br />
können Kabel auch bis<br />
max. 25 mm Ø getrennt werden<br />
• scharfe, gehärtete Schneiden mit Präzisionsschliff<br />
• leichter, sauberer Schnitt bei Einhandbetätigung<br />
• nachstellbares Schraubgelenk<br />
• nicht für Stahldraht, Drahtseil und<br />
hartgezogene Kupferleiter geeignet<br />
• Werkstoff: Spezialwerkzeugstahl, geschmiedet<br />
patentiert<br />
patented<br />
Art. No. Ausführung Griffe Schneidwerte Länge<br />
Finish Handles Cutting capacity Length<br />
mm mm 2 mm g<br />
600 020 3 brüniert Kunststoff überzogen 20 70 200 300<br />
burnished plastic coated<br />
600 020 36 brüniert starkw. Kunststoffgriff 20 70 200 340<br />
burnished reinforced plastic grips<br />
600 020 6 verchromt Kunststoff überzogen 20 70 200 300<br />
chrome plated plastic coated<br />
600 020 66 verchromt starkw. Kunststoffgriff 20 70 200 340<br />
chrome plated reinforced plastic grips<br />
• low effort required due to high transmission ratio<br />
and new blade geometry<br />
• no crushing, no deformation<br />
• initial and final cut (1st and 2nd blades)<br />
allow cables with a diameter of up to<br />
max. 25 mm Ø to be cut<br />
• sharp, hardened, precision-ground blades<br />
• easy, clean cut with one hand operation<br />
• adjustable joint screw<br />
• not suitable for steel wire, wire cable<br />
and hard-drawn copper cables<br />
• Material: special tool steel,<br />
forged<br />
Phase 1: Vorschnitt<br />
Initial cut<br />
Durch Einsatz der vorderen Schneide bleibt<br />
selbst bei größeren Kabeldurchmessern<br />
noch eine ergonomische<br />
Schenkelweite erhalten.<br />
The use of the front blade means<br />
that an ergonomic handle width is retained<br />
even when handling large diameter cables.<br />
Phase 2: Fertigschnitt<br />
Final cut<br />
Bei größerem Kraftbedarf ist ein Nachsetzen<br />
in das Profil am Gelenk möglich.<br />
Vorschnitt vorne-Fertig-Schnitt hinten.<br />
If greater force is required, it is possible<br />
to adjust the profile at the joint.<br />
Initial cut at the front, final cut at the rear.<br />
9