Pipe Components 2011 - Van Leeuwen Buizen

Product descriptions pipe components DIN - EN
Product group Standard Steel grade Full description
729 DIN 2642 P235GH / P250GH Slip on flanges as per DIN 2642 Type F, drilled out to PN 10 manufactured from material
S235JR as per EN 10025 or material P235GH as per EN 10028-2 or material P250GH as
per DIN-EN 10222-2, with additional requirements as per AD Merkblatt W9, TRD107 and
PED 97/23/EC. If desired with inspection report as per EN 10204/3.1.
729 DIN 2642 P235GH / P250GH Rings (Bunde) as per DIN 2642 Type B manufactured from material S235JR as per EN
10025 or material P235GH as per EN 10028-2 or material P250GH as per DIN-EN 10222-2,
with additional requirements as per AD Merkblatt W9, TRD107 and PED 97/23/EC. If
desired with inspection report as per EN 10204/3.1.
731 DIN 2609 / EN 10253 St.35.8 / P235GH Seamless steel fittings as per DIN 2609 (Part 2) or EN 10253-2 manufactured from
material St.35.8/1 or P235GH, with additional requirements as per VdTUEV Merkblatt
1252 and PED 97/23/EC, with bevelled ends for wall thickness > 3 mm, stamped with
heat number or identification number, material type and manufacturer’s symbol.
Fitting types as per EN 10253-2:
Tees (DIN 2615) and eccentric reducers (DIN 2616), Type A
Concentric reducers (DIN 2616), Type B
Eccentric reducers (DIN 2616), Type A
Caps (DIN 2617), Type A
Saddles: dimensions as per DIN 2618
DIN 2619 equivalent elbows
If desired with inspection report as per EN 10204/3.1.
731 DIN 28011 S235JR Seamless convex caps (“Klöpper”) as per DIN 28011, cold formed, manufactured from
material S235JRG2 as per EN 10025 (RSt 37.2), with bevelled ends for wall thickness > 3
mm. If desired with test report as per EN 10204/2.2.
731 DIN 2617 / DIN 28013 P265GH Seamless convex caps as per DIN 2617 / elliptical caps as per DIN 28013 Type VA bevelled
manufactured from material P265GH as per EN 10028 (heavy steel plate H II as per DIN
17155), with bevelled ends for wall thickness > 3 mm. If desired with inspection report as
per EN 10204/3.1.
733 DIN 2987 / EN 10241 Elbow 90° (No. 13) female threaded as per DIN 2987/1, water pressure tested at 75 bar.
Thread: Whitworth as per DIN 2999 Part 1. Execution: black.
734 DIN 2987 / EN 10241 Elbow 90° (No. 13) female threaded as per DIN 2987/1, water pressure tested at 75 bar.
Thread: Whitworth as per DIN 2999 Part 1. Execution: galvanized.
733 DIN 2986 / EN 10241 Straight couplings (No. 16) female threaded as per DIN 2986, water pressure tested at 75
bar. Thread: Whitworth as per DIN 2999 Part 1. Execution: black.
734 DIN 2986 / EN 10241 Straight couplings (No. 16) female threaded as per DIN 2986, water pressure tested at 75
bar. Thread: Whitworth as per DIN 2999 Part 1. Execution: galvanized.
733 DIN 2982 / EN 10241 Threaded nipples (No. 22) male threaded as per DIN 2982 or EN 10241, water pressure
tested at 50 bar. Thread: Whitworth as per DIN 259. Execution: black.
734 DIN 2982 / EN 10241 Threaded nipples (No. 22) male threaded as per DIN 2982 or EN 10241, water pressure
tested at 50 bar. Thread: Whitworth as per DIN 259. Execution: galvanized.
733 DIN 2982 / EN 10241 Pipe nipples (No. 23) male threaded at both ends as per DIN 2982 or EN 10241, water
pressure tested at 50 bar. Thread: Whitworth as per DIN 2999 Part 1. Execution: black.
734 DIN 2982 / EN 10241 Pipe nipples (No. 23) male threaded at both ends as per DIN 2982 or EN 10241, water
pressure tested at 50 bar. Thread: Whitworth as per DIN 2999 Part 1. Execution:
galvanized.
14 No part of this publication may be multiplied or copied without previous written permission of Van Leeuwen Pipe and Tube