Tray Cable - IEWC

Customer Driven • Solution Focused
...we’ve got you covered!
Complete catalog available: www.iewc.com

Index
Tray Cable
Small Diameter Neoprene Control Cable
18 AWG - 16 AWG
14 AWG - 12 AWG
Vinyl Nylon Tray Cable (VNTC)
Building Wire
18 AWG - 16 AWG, TFN Conductors
14 AWG - 12 AWG, THHN/THWN Conductors
Power Limited Tray Cable (PLTC)
22 AWG - 14 AWG, Unshielded
22 AWG - 14 AWG, Shielded
TFFN/THHN
XHHW
Welding Cable
Stranded Class K (30 AWG stranding)
Flex Stranded Class M (34 AWG stranding)
Welding Cable Ampacity Chart
Color Code Charts
ICEA Method 1, Table E1
ICEA Method 1, Table E2
Disclaimer: The values and data shown in this catalog represent typical values intended to distinguish one material from
another and to serve as a guide in selecting the proper material for specific applications or end uses. The information
containted herein is given in good faith, but because of the many variables in subsequent manufacturing and installation
operations, no guarantees can be made for the performance of these products in service. Users are requested to make
their own tests to determine the suitability of these materials for the applications and to be guided by the results of
such tests.
Data and suggestions made in this publication are not to be construed as recommendations to use any product in
violation of existing patents covering any material or its use.
2
Page
3
4
5
6
7
8
9
10
11
12
13
14
14
15
6, 9
3

Small Diameter Neoprene
Flexible Control Cable (SDN )
UL Listed as Type TC Tray Cable, CSA Type CIC TC
600 Volts, 90°C to - 40°C
Description:
• Soft annealed bare flexible copper.
•
• Thermoplastic rubber insulation, color coded, a .005 min nylon
coating over the flame retardant insulation provides mechanical
protection and slippage between conductors for better flexing.
Meets UL 1277 and IEEE 383 flame test at 70,000 BTU/hr. •
• Jute or nylon fillers are used as required and a mylar binder
holds the conductors together and reduces friction.
•
• Color coded per ICEA method 1 table E2.
UL 600V, 90°C Dry, 75°C Wet
Color Code Chart
Per ICEA Method 1 Table E2
COND.
NO.
COLOR
BASE
SPIRAL
STRIPE
COND.
NO.
COLOR
BASE
Note: Beyond 36 conductors, color code repeats starting at #1.
Application:
Designed for control, power, lighting, telemetering,
signal, relay traffic control, wherever flexible small
diameter cable is required such as cranes, hoists,
and some robotic applications
Recommended for wet or dry locations and outdoors
in cable trays where a sunlight resistant rating is
required.
SPIRAL
STRIPE
COND.
NO.
COLOR
BASE
SPIRAL
STRIPE
1 Black 13 Blue Red 25 Yellow Orange
2 Red - 14 Orange Red 26 Brown Orange
3 Blue - 15 Yellow Red 27 Black Yellow
4 Orange - 16 Brown Red 28 Red Yellow
5 Yellow - 17 Black Blue 29 Blue Yellow
6 Brown - 18 Red Blue 30 Orange Yellow
7 Red Black 19 Orange Blue 31 Brown Yellow
8 Blue Black 20 Yellow Blue 32 Black Brown
9 Orange Black 21 Brown Blue 33 Red Brown
10 Yellow Black 22 Black Orange 34 Blue Brown
11 Brown Black 23 Red Orange 35 Orange Brown
12 Black Red 24 Blue Orange 36 Yellow Brown
See Page 9 for Color Code Chart E1
3
®
To be installed in trays, raceways, troughs, channels,
ducts, conduit and by direct burial.

Small Diameter Neoprene
Control Cable (SDN ® )
600 Volts, 90°C to - 40° C, UL Type TC
18 AWG 16/30 Bare Copper
Insulation: .015 Thickness
INDUSTRIAL
ELECTRIC
PART#
NO. OF
COND.
JACKET
THICKNESS
MILS.-NOM.
DIAMETER
INCHES
NOM.
APPROX.
NET WT.
# /1000 FT
SDN1802* 2 45 0.275 46
SDN1803 3 45 0.285 50
SDN1804* 4 45 0.315 60
SDN1805 5 45 0.335 71
SDN1806 6 45 0.360 83
SDN1807* 7 45 0.380 106
SDN1808 8 45 0.420 109
SDN1809* 9 45 0.450 120
SDN1810 10 45 0.450 126
SDN1811* 11 45 0.470 135
SDN1812 12 45 0.465 142
SDN1813* 13 45 0.490 153
SDN1814 14 45 0.485 165
SDN1815* 15 45 0.515 170
SDN1816 16 45 0.510 175
SDN1817* 17 60 0.590 230
SDN1818* 18 60 0.590 230
SDN1819 19 60 0.590 240
SDN1821* 21 60 0.605 270
SDN1824 24 60 0.660 285
SDN1825* 25 60 0.680 300
SDN1830* 30 60 0.695 335
SDN1837* 37 60 0.775 386
* NOT A NORMAL STOCK ITEM
16 AWG 19/29 Bare Copper
Insulation: .015 Thickness
INDUSTRIAL
ELECTRIC
PART#
NO. OF
COND.
JACKET
THICKNESS
MILS.-NOM.
DIAMETER
INCHES
NOM.
CONTACT YOUR SALES REPRESENTATIVE FOR SPECIAL SIZES AND SHIELDED CONSTRUCTIONS
4
SDN1602 2 45 0.290 51
SDN1603 3 45 0.305 62
SDN1604 4 45 0.330 77
SDN1605* 5 45 0.360 92
SDN1606 6 45 0.390 107
SDN1607 7 45 0.420 123
SDN1608 8 45 0.450 137
SDN1609 9 45 0.475 165
SDN1610 10 45 0.485 165
SDN1611* 11 45 0.500 180
SDN1612 12 45 0.500 188
SDN1613* 13 60 0.555 225
SDN1614* 14 60 0.555 240
SDN1615* 15 60 0.585 255
SDN1616 16 60 0.585 258
SDN1617* 17 60 0.635 290
SDN1618* 18 60 0.635 290
SDN1619 19 60 0.635 296
SDN1621* 21 60 0.650 340
SDN1624 24 60 0.715 367
SDN1625* 25 60 0.730 380
SDN1630 30 60 0.750 432
SDN1637 37 80 0.870 556
SDN1660* 60 80 1.045 953
APPROX.
NET WT.
# /1000 FT

Small Diameter Neoprene
Control Cable (SDN ® )
600 Volts, 90°C to - 40°C, UL Type TC
14 AWG 19/27 Bare Copper
Insulation: .015 Thickness
INDUSTRIAL
ELECTRIC
PART#
NO. OF
COND.
JACKET
THICKNESS
MILS.-NOM.
DIAMETER
INCHES
NOM.
APPROX.
NET WT.
# /1000 FT
12 AWG 19/25 Bare Copper
Insulation: .015 Thickness
INDUSTRIAL
ELECTRIC
PART#
NO. OF
COND.
JACKET
THICKNESS
MILS.-NOM.
DIAMETER
INCHES
NOM.
SDN1402* 2 45 0.320 78 SDN1202* 2 45 0.360 109
SDN1403 3 45 0.340 84 SDN1203 3 45 0.380 115
SDN1404 4 45 0.370 104 SDN1204 4 45 0.415 146
SDN1405 5 45 0.400 127 SDN1205 5 45 0.450 177
SDN1406 6 45 0.435 147 SDN1206 6 45 0.490 209
SDN1408 8 45 0.505 200 SDN1207* 7 60 0.570 230
SDN1409* 9 60 0.570 235 SDN1208 8 60 0.605 294
SDN1410 10 60 0.580 246 SDN1209* 9 60 0.650 325
SDN1412 12 60 0.595 290 SDN1210 10 60 0.655 350
SDN1413* 13 60 0.625 305 SDN1211* 11 60 0.675 375
SDN1414* 14 60 0.625 325 SDN1212 12 60 0.675 395
SDN1415* 15 60 0.655 340 SDM1213* 13 60 0.700 430
SDN1416 16 60 0.655 354 SDN1214* 14 60 0.720 455
SDN1417* 17 60 0.725 400 SDN1215 15 60 0.730 480
SDN1418* 18 60 0.725 410 SDN1216* 16 60 0.755 505
SDN1419* 19 60 0.725 430 SDN1217* 17 60 0.800 530
SDN1421* 21 60 0.740 470 SDN1218* 18 60 0.800 555
SDN1424* 24 60 0.805 510 SDN1219* 19 80 0.800 605
SDN1425* 25 80 0.875 520 SDN1221* 21 80 0.880 680
SDN1430* 30 80 0.875 660 SDN1224 24 80 0.955 773
SDN1437* 37 80 0.990 785 SDN1225 25 80 0.970 782
* NOT A NORMAL STOCK ITEM
CONTACT YOUR SALES REPRESENTATIVE FOR SPECIAL SIZES AND SHIELDED CONSTRUCTIONS
5
APPROX.
NET WT.
# /1000 FT
SDN1230* 30 80 1.010 1032
SDN1237* 37 80 1.145 1120

Tray Cable (VNTC)
Multi-conductor, Unshielded
TFN, THWN or THHN Conductors
PVC Jacket, 600 Volts
Description:
● Conductors: Stranded Bare Copper
● Singles Insulation: PVC/Nylon
● Singles Rated: THHN, THWN OR TFN
● Color Code: ICEA Method 1, Table E2
(formerly Table K2) Per ICEA S-73-532
● Conductors: Black PVC
● Rated as UL listed TC 90 C, 75 C wet.
70,000 BTU per IEEE 383 Vertical Tray
Fire Test
Color Code Chart
Per ICEA Method 1 Table E2
COND.
NO.
COLOR
BASE
SPIRAL
STRIPE
COND.
NO.
Note: Beyond 36 conductors, color code repeats starting at #1.
See Page 3 for Color Code Chart E1
COLOR
BASE
Application:
● For use in power, lighting, control and signal
circuits. These cables may be installed in
wet or dry locations; cable trays, raceways,
open air and conduits. Also suitable for
exposure to weather, direct burial and for
Class I, Div. 2 and Class II, Div. 2 for hazardous
locations per NEC.
6
SPIRAL
STRIPE
COND.
NO.
COLOR
BASE
SPIRAL
STRIPE
1 Black 13 Blue Red 25 Yellow Orange
2 Red - 14 Orange Red 26 Brown Orange
3 Blue - 15 Yellow Red 27 Black Yellow
4 Orange - 16 Brown Red 28 Red Yellow
5 Yellow - 17 Black Blue 29 Blue Yellow
6 Brown - 18 Red Blue 30 Orange Yellow
7 Red Black 19 Orange Blue 31 Brown Yellow
8 Blue Black 20 Yellow Blue 32 Black Brown
9 Orange Black 21 Brown Blue 33 Red Brown
10 Yellow Black 22 Black Orange 34 Blue Brown
11 Brown Black 23 Red Orange 35 Orange Brown
12 Black Red 24 Blue Orange 36 Yellow Brown

Tray Cable (VNTC)
Multi-conductor, Unshielded
TFN Conductors
UL TYPE TC 600 Volts, 18 - 16 AWG
Cable Specifications:
Conductors: Stranded Bare Copper
Singles Insulation: PVC/NYLON
Color Code: ICEA Method 1, Table E2 (formerly Table K2) Per ICEA S-73-532
Jacket: Black PVC
Ratings: UL Listed Type TC 90°C dry, 75°C wet VW-1
TFN Singles
70,000 BTU per IEEE-383 Vertical Tray Fire Test
INDUSTRIAL
ELECTRIC
PART*
NO. OF
CONDS. STRAND
INSULATION
THICKNESS
MILS.-NOM.
NYLON
INSULATION
MILS.-NOM.
JACKET
THICKNESS
MILS.-NOM.
TC1802F/P 2 Flat 7 BC 15 4 45 .180 X .270 35
TC1803P 3 7 BC 15 4 45 0.290 45
TC1804P 4 7 BC 15 4 45 0.310 54
TC1805P 5 7 BC 15 4 45 0.340 66
TC1807P 7 7 BC 15 4 45 0.360 82
TC1809P 9 7 BC 15 4 45 0.420 108
TC1812P 12 7 BC 15 4 45 0.470 131
TC1815P 15 7 BC 15 4 45 0.500 160
TC1819P 19 7 BC 15 4 60 0.570 210
TC1825P 25 7 BC 15 4 60 0.660 272
TC1837P 37 7 BC 15 4 60 0.750 380
TC1602F/P 2 Flat 7 BC 15 4 45 .190X.290 45
TC1603P 3 7 BC 15 4 45 0.310 59
TC1604P 4 7 BC 15 4 45 0.330 71
TC1605P 5 7 BC 15 4 45 0.360 86
TC1607P 7 7 BC 15 4 45 0.390 110
TC1609P 9 7 BC 15 4 45 0.450 141
TC1612P 12 7 BC 15 4 45 0.510 179
TC1615P 15 7 BC 15 4 60 0.570 232
TC1619P 19 7 BC 15 4 60 0.610 283
TC1625P 25 7 BC 15 4 60 0.720 367
TC1630P 30 7 BC 15 4 60 0.770 430
TC1637P 37 7 BC 15 4 80 0.860 548
Note: Dimensons and weights shown are nominal values. They are subject to standard industry tolerances.
7
DIAMETER APPROX.
INCHES NET WT.
NOM. # /1000 FT

Tray Cable (VNTC)
Multi-conductor, Unshielded
THHN/THWN CONDUCTORS
UL TYPE TC 600 Volts, 14 - 12 AWG
Cable Specifications:
Conductors: Stranded Bare Copper
Singles Insulation: PVC Insulation with nylon armour
Color Code: ICEA Method 1 colors per table K-2.
Jacket: Black PVC
Ratings: UL Listed Type TC 90 C dry, 75 C wet VW-1
(THN/THWN Only) IEE383
70,000 and 210,000 BTU.
INDUSTRIAL
ELECTRIC
PART*
NO. OF
CONDS. STRAND
INSULATION
THICKNESS
MILS.-NOM.
NYLON
INSULATION
MILS.-NOM.
TC1402F/P 2 Flat 7 BC 15 4 45 .205 X .315 58
TC1403P 3 7 BC 15 4 45 0.340 90
TC1404P 4 7 BC 15 4 45 0.370 96
TC1405P 5 7 BC 15 4 45 0.400 117
TC1407P 7 7 BC 15 4 45 0.430 152
TC1409P 9 7 BC 15 4 45 0.500 195
TC1412P 12 7 BC 15 4 45 0.590 266
TC1415P 15 7 BC 15 4 60 0.640 326
TC1419P 19 7 BC 15 4 60 0.690 396
TC1425P 25 7 BC 15 4 60 0.790 518
TC1430P 30 7 BC 15 4 60 0.890 638
TC1437P 37 7 BC 15 4 60 0.950 774
TC1202F/P 2 Flat 7 BC 15 4 45 .225 X .359 77
TC1203P 3 7 BC 15 4 45 0.380 105
TC1204P 4 7 BC 15 4 45 0.410 135
TC1205P 5 7 BC 15 4 45 0.450 166
TC1206P 6 7 BC 15 4 45 0.490 196
TC1207P 7 7 BC 15 4 45 0.490 215
TC1209P 9 7 BC 15 4 60 0.600 304
TC1212P 12 7 BC 15 4 60 0.670 376
TC1215P 15 7 BC 15 4 60 0.720 470
TG1219P 19 7 BC 15 4 60 0.780 573
TC1225P 25 7 BC 15 4 80 0.950 778
TC1230P 30 7 BC 15 4 80 1.010 915
TC1237P 37 7 BC 15 4 80 1.090 1107
Note: Dimensons and weights shown are nominal values. They are subject to standard industry tolerances.
8
JACKET DIAMETER APPROX.
THICKNESS INCHES NET WT.
MILS.-NOM. NOM. # /1000 FT

Tray Cable (PLTC)
Instrumentation Cable
PVC Conductors
UL TYPE PLTC 300 V
Description:
● Conductors: Stranded Tinned Copper
● Singles Insulation: PVC
● Color Code: ICEA Method 1, Table E1 or E2
● Jacket: Gray PVC
● Sunlight and Oil resistant jacket
● Rated as UL listed PLTC, ITC, 105°C
● Meets UL 1685 Vertical Flame Test
Color Code Chart
Per ICEA Method 1 Table E-1
COND.
NO.
COLOR
BASE STRIPE
COND.
NO.
COLOR
BASE STRIPE
COND.
NO.
COLOR
BASE STRIPE
1 Black - 13 Red White 25 Green Black/White
2 White - 14 Green White 26 Orange Black/White
3 Red - 15 Blue White 27 Blue Black/White
4 Green - 16 Black Red 28 Black Red/Green
5 Orange - 17 White Red 29 White Red/Green
6 Blue - 18 Orange Red 30 Red Black/Green
7 White Black 19 Blue Red 31 Green Black/Orange
8 Red Black 20 Red Green 32 Orange Black/Green
9 Green Black 21 Orange Green 33 Blue White/Orange
10 Orange Black 22 Black White/Red 34 Black White/Orange
11 Blue Black 23 White Black/Red 35 White Red/Orange
12 Black White 24 Red Black/White 36 Orange White/Blue
See Page 6 for Color Code Chart E2
Application:
Unshielded - Twisted non-shielded paris and triads
provide a minimal OD allowing greater tray and
conduit fill.
Overall Shield - Recommended for use in
instrumentation applications where signals are
transmitted in excess of 100 millivolts except in
areas where high voltage and current sources
create excessive noise interference.
9

Tray Cable (PLTC)
Instrumentation Cable
PVC Conductors
UL TYPE PLTC 300V
Cable Specifications:
Conductors: Stranded Tinned Copper
Singles Insulation: PVC
Color Code: ICEA Method 1, Table E1 or E2
Jacket: Gray PVC
UNSHIELDED
INDUSTRIAL
ELECTRIC
PART #
AWG
PAIR/
TRIAD
STRAND
Ratings:
UL listed PLTC, ITC, 105°C
Meets UL1685 Vertical Flame Test
Sunlight and Oil resistant jacket
INSULATION
THICKNESS
MILS.-NOM.
COLOR
CODE
JACKET
THICKNESS
MILS.-NOM.
PLTC2202P 22 1 Pair 7x30 0.016 E2 0.037 0.198 16.7
PLTC2203T 22 1 Triad 7x30 0.016 E1 0.037 0.208 23
PLTC2002P 20 1 Pair 19x32 0.016 E2 0.037 0.214 23
PLTC2003T 20 1 Triad 19x32 0.016 E1 0.037 0.225 27
PLTC1802P 18 1 Pair 19x30 0.017 E2 0.037 0.230 27
PLTC1803T 18 1 Triad 19x30 0.017 E1 0.037 0.242 35.9
PLTC1602P 16 1 Pair 19x29 0.016 E1 0.037 0.254 34
PLTC1603T 16 1 Triad 19x29 0.016 E1 0.037 0.268 48.5
PLTC1402P 14 1 Pair 42x30 0.022
E2 0.042 0.322 58
PLTC1403T 14 1 Triad 42x30 0.022 E1 0.042 0.340 76.3
10
DIAMETER APPROX.
INCHES NET WT
NOM. #/ 1000 FT

Tray Cable (PLTC)
Instrumentation Cable
PVC Conductors
UL TYPE PLTC 300V
Cable Specifications:
Conductors: Stranded Tinned Copper
Singles Insulation: PVC
Color Code: ICEA Method 1, Table E1 or E2
Jacket: Gray PVC
Shield: Overall Foil
SHIELDED
INDUSTRIAL
ELECTRIC
PART #
AWG
PAIR/
TRIAD
STRAND
Ratings:
UL listed PLTC, ITC, 105°C
Meets UL1685 Vertical Flame Test
Sunlight and Oil resistant jacket
INSULATION
THICKNESS
MILS.-NOM.
PLTC2202POFS 22 1 Pair 7x30 0.016 E2 0.037 0.201 21
PLTC2204POFS 22 2 Pair 7x30 0.016 E2 0.042 0.310 37
PLTC2203TOFS 22 1 Triad 7x30 0.016 E1 0.037 0.208 26
PLTC2002POFS 20 1 Pair 19x32 0.016 E2 0.037 0.217 26
PLTC2003TOFS 20 1 Triad 19x32 0.016 E1 0.037 0.228 31
PLTC1802POFS 18 1 Pair 19x30 0.017 E2 0.037 0.233 32
PLTC1804POFS 18 2 Pair 19x30 0.017 E2 0.042 0.368 59
PLTC1602POFS 16 1 Pair 19x29 0.017 E2 0.037 0.256 41
PLTC1402POFS 14 1 Pair 42x30 0.022 E2 0.042 0.324 67
11
COLOR
CODE
JACKET
THICKNESS
MILS.-NOM.
PLTC1803TOFS 18 1 Triad 19x30 0.016 E1 0.037
PLTC1603TOFS 16 1 Triad 19x29 0.016 E1 0.037
DIAMETER APPROX.
INCHES NET WT
NOM. #/ 1000 FT
0.245 39
0.270 53
PLTC1403TOFS 14 1 Triad 42x30 0.022
E1 0.042 0.343 86

TFFN/THHN Building Wire
90°C, 600 Volts, C(UL) T90 Nylon
Description:
● Conductor of soft drawn bare copper, concentric,
compressed concentric, or combination unilay.
● Singles Insulation: PVC/Nylon
● Listed by Underwriters Laboratories under
standards 83 and 1063 as:
-Type THHN 90 C in dry locations
-Type THWN 75 C in wet locations
-Gasoline and oil resistant.
-Type MTW 90 C Machine Tool Wire (stranded
only)
-105 C AWM, 80 C where exposed to oil.
● TFFN is UL 1315, 105 C approved & CSA
TEWN approved
INDUSTRIAL
ELECTRIC
PART# AWG
NO. OF
STRANDS
INSULATION
THICKNESS
MILS-NOM
NYLON
INSULATION
MILS-NOM
Application:
● General Purpose wiring in accordance
with the NEC, maximum conductor
temperature of 90 C in dry locations and
75 C in wet locations, 600 volts for
installation in conduit or other recognized
race way. For wiring of machine tools
(stranded), appliances and control
circuits not exceeding 600 volts.
DIAMETER
INCHES
NOM.
APPROX.
NET WT.
#/1000 FT
RoHS compliant material available upon request.
*Listed as 105 C Appliance Wiring Material and 90 C MTW, also as Type TFFN (stranded conductor)
and TFN (solid conductor) 90 C, CSA approved as Type TEWN.
**Ampacity in accordance with NEC
As THHN 90 C, conductor temperature at 30 C ambient in dry locations.
As THHN 75 C, conductor temperature at 30 C ambient in wet or dry locations.
NEC AMPACITY**
75°C 90°C
THWN THHN
TFN18B01* 18 SOLID 15 5 0.083 8 0 6
TFN16B01* 16 SOLID 15 5 0.094 11 0 8
TFFN18B16* 18 16 16 5 0.090 8 0 6
TFFN16B26* 16 26 16 5 0.103 12 0 8
THHN14B01 14 SOLID 15 4 0.104 16 15 15
THHN12B01 12 SOLID 15 4 0.121 24 20 20
THHN10B01 10 SOLID 20 4 0.152 38 30 30
THHN14B19 14 19 15 4 0.112 17 15 15
THHN12B19 12 19 15 4 0.131 26 20 20
THHN10B19 10 19 20 4 0.164 40 30 30
THHN08B19 8 19 30 5 0.216 66 50 55
THHN06B19 6 19 30 5 0.253 100 65 75
THHN04B19 4 19 40 6 0.322 159 85 95
THHN03B19 3 19 40 6 0.350 191 100 110
THHN02B19 2 19 40 6 0.381 241 115 130
THHN01B19 1 19 50 7 0.443 305 130 150
THHN1/0B19 1/0 19 50 7 0.483 377 150 170
THHN2/0B19 2/0 19 50 7 0.528 468 175 195
THHN3/0B19 3/0 19 50 7 0.579 581 200 225
THHN4/0B19 4/0 19 50 7 0.636 722 230 260
THHN250B37 250 37 60 8 0.704 860 255 290
THHN300B37 300 37 60 8 0.758 1018 310 350
THHN350B37 350 37 60 8 0.808 1180 310 350
THHN400B37 400 37 60 8 0.855 1342 335 380
THHN500B37 500 37 60 8 0.938 1661 380 430
12

XHHW-2 Building Wire
90°C, 600 Volts
Description:
● Conductor of soft drawn bare copper
with concentric stranding
● Singles Insulation: Crosslinked
polyethylene (XLPE)
● Listed by Underwriters Laboratories as
type XHHW-2 per UL standard 44.
Application:
● General purpose wiring in accordance
with the NEC, maximum conductor
temperature of 90 C in wet or dry
locations
INDUSTRIAL
INSULATION DIAMETER APPROX.
ELECTRIC
NO. OF THICKNESS INCHES NET WT. NEC AMPACITY*
PART # AWG STRANDS MILS. - NOM. NOM. # /1000 FT
75°C 90°C
XHHW14B07 14 7 30 0.133 18 15 25
XHHW12B07 12 7 30 0.152 27 20 30
XHHW10B07 10 7 30 0.175 39 30 40
XHHW08B07 8 7 45 0.235 66 50 55
XHHW06B07 6 7 45 0.275 99 65 75
XHHW04B07 4 7 45 0.320 151 85 95
XHHW02B07 2 7 45 0.380 232 115 130
XHHW01B19 1 19 55 0.440 300 130 150
XHHW1/0B19 1/0 19 55 0.480 372 150 170
XHHW2/0B19 2/0 19 55 0.525 461 175 195
XHHW3/0B19 3/0 19 55 0.575 573 200 225
XHHW4/0B19 4/0 19 55 0.635 714 230 260
XHHW250B37 250 37 65 0.700 846 255 290
XHHW300B37 300 37 65 0.755 1005 285 320
XHHW350B37 350 37 65 0.805 1166 310 350
XHHW400B37 400 37 65 0.850 1318 335 380
XHHW500B37 500 37 65 0.935 1642 380 430
XHHW600B61 600 61 80 1.045 1986 420 475
XHHW750B61 750 61 80 1.145 2453 475 535
RoHS compliant material available upon request.
* Ampacity in accordance with NEC for not more than three conductors in raceway.
90°C conductor temperature at 30°C ambient in dry locations.
90°C conductor temperature at 30°C ambient in wet locations.
13

Welding Cable
Application
● Secondary voltage resistance welding leads
● Power Supply appllications not exceeding 600 Volt AC
● Sizes 1/0 and larger for permanent wiring in conduit or tray of 600V power supplies,
hoists, cranes or other applications where flexible power leads may be installed in
conduit, raceways or tray.
Class K (30 AWG STRAND)
600 Volts 105°C - 50°C
INDUSTRIAL
ELECTRIC
PART# AWG
NO. OF
STRANDS
NOTE: Stranding may vary slightly by manufacturer.
Flexible bare copper conductor
EPDM Insulation, Color Black
Red insulation available upon request.
INSULATION
THICKNESS
MILS. - NOM.
Welding Cable, Extra Flexible
UL Listed, Class M (34 AWG Strand)
o o
600 Volts, 90 C - 50 C
14
DIAMETER
INCHES
NOM.
WC06 6 266/30 0.060 0.320 116
WC04 4 392/30 0.060 0.375 163
WC02 2 644/30 0.060 0.440 251
WC01 1 784/30 0.080 0.515 321
WC1/0 1/0 1026/30 0.080 0.550 388
WC2/0 2/0 1254/30 0.080 0.590 474
WC3/0 3/0 1615/30 0.080 0.660 601
WC4/0 4/0 2052/30 0.080 0.725 762
INDUSTRIAL
ELECTRIC
PART*
AWG
NO. OF
STRANDS
INSULATION
THICKNESS
MILS. - NOM.
DIAMETER
INCHES
NOM.
WC06 6
660/34 0.078 0.370 125
WC04 4
1045/34 0.082 0.420 190
WC02 2
1650/34 0.091 0.475 260
WC01 1
2090/34 0.091 0.525 325
WC1/0 1/0
2640/34 0.095 0.610 410
WC2/0 2/0
3300/34 0.095 0.635 495
WC3/0 3/0
4180/34 0.104 0.700 620
WC4/0 4/0
5225/34 0.115 0.800 795
NOTE: Stranding may vary slightly by manufacturer.
Extra flexible bare copper conductor
CPE Insulation, Color Orange
Oil Resistant
APPROX.
NET WT.
#/ 1000 FT
APPROX.
NET WT.
# /1000 FT

Welding Cable Ampacities
Required Cable Sizes:
For Arc Welding Cable Application
Length in feet for total circuit* for secondary voltages only
- do not use this table for 600 volt applications.
AMPS 100' 150' 200' 250' 300' 350' 400'
100 4 4 2 2 1 1/0 1/0
150 4 2 1 1/0 1/0 3/0 3/0
200 2 1 1/0 2/0 3/0 4/0 4/0
250 1 1/0 2/0 3/0
300 1/0 2/0 3/0 4/0
350 2/0 3/0 4/0
400 2/0 3/0
450 2/0 4/0
500 3/0 4/0
550 3/0 4/0
600 4/0 REQUIRED CABLE SIZES SHOW IN GUAGE NUMBERS
*The total circuit length includes both welding and ground leads (based on 4-volt drop) 60% duty cycle
These values for current-carrying capacity are based on a copper temperature of 60 C (140 F), an
ambient temperature of 40 C (104 F), and yield load factors from approximately 32% for the 2 AWG
cable to approximately 23% for the 3/0 AWG Cable, and higher for the smaller sizes. The sizes of
cables generally used range from 2 AWG to 3/0 AWG. In actual service, the load factor may be much
higher than indicated without overheating the cable as the ambient temperature will generally be
substantially lower than -40 C.
Suggested Ampacities
For 600 Volt In-Line Applications
AWG AMPERES AWG AMPERES
4/0 315 1 170
3/0 275 2 150
2/0 235 3 130
1/0 200 4 110
6 85
15
Per standards: ICEA S-19-81
NEMA WC-3 Part 8, Appendix J
Ampacities for portable cable,
continuous duty (Ambient Temperature
of 40 C)